Pass the Cisco CCNP Service Provider 350-501 Questions and answers with ExamsMirror

What is a characteristic of data modeling language?

Which statement about the Cisco MPLS TE forwarding adjacency feature is true?

Refer to the exhibit. Which additional configuration must an engineer to the adge router to inject a default router into the MP-BGP address family for the internet_Shared_Services dedicated VRF?

A)

B)

C)

D)

Refer to the exhibit. A network engineer received a complaint about these problems in OSPF stub area 100:

The Ethernet link is down between routers RX and RY because the fiber was cut.

CE site A traffic to the hub site is being dropped.

Which action resolves these issues?

Refer to the exhibit.

An engineer is configuring path selection on router R1 for two ASNs as shown. Which additional task must the engineer perform on Router 1 so that all outbound traffic utilizes the link between R1 and R3 to reach ASN 4567?

Refer to the exhibit:

This configuration is being applied on an IOS XR router.

Which statement about this configuration is true?

Refer to the exhibit. An engineer configured several network devices to run REST APIs. After testing, the organization plans to use REST APIs throughout the network to manage the network more efficiently. What is the effect if this script?

Refer to the exhibit:

An engineer wants to authenticate the OSPF neighbor between PEA and PE-B using MD5.

Which command on PE-B successfully completes the configuration?

A)

B)

C)

D)

Refer to the exhibit. A network engineer is implementing multicast Source-A to send a multicast stream for Receiver-A, and multicast Source-B to send a multicast stream for Receiver-B. Router RC forwards the IGMP host a report and leaves messages to IP address 192.168.10.1. How must the multicast features be implemented to prevent RB from receiving multicast flooding from Source-A?

Guidelines -

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab closes and cannot be reopened.

Topology:

Tasks -

Configure the BGP routing protocol for R1 and R2 according to the topology to achieve these goals:

1. Configure EBGP neighbor adjacency for the IPv4 and IPv6 address family between R1 and R2 using Loopback0 IPv4 and IPv6 addresses. All BGP updates must come from the Loopback0 interface as the source. Do not use IGP routing protocols to complete this task.

2. Configure MD5 Authentication for the EBGP adjacency between R1 and R2. The password is clear text C1sc0!.

Refer to the exhibit.

A network engineer must implement SNMPv3 on a Cisco IOS XR router running BGP. The engineer configures SNMPv3 to use SHA for authentication and AES for privacy on the routers, which are in a different data center in the same exchange as other routers. The engineer must also verify the associated MIB view family name, storage type, and status. Which set of actions meets these requirements?

Drag and drop the multicast concepts from the left onto the correct descriptions on the right.

Refer to the exhibit.

A network engineer Is implementing OSPF multiarea. Which command on interface G0/1 resolves adjacency Issues in the new area?

A network engineer is adding 10Gbps link to an existing 2X1Gbps LACP-based LAG to augment its capacity. Network standards require a bundle interface to be take out of service if one of its member links does down, and the new link must be added with minimal impact to the production network. Drag and drop the tasks that the engineer must perform from the left into the sequence on the right. Not all options are used.

Refer to the exhibit:

With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?