Pass the CWNP CWAP Wi-Fi Analysis CWAP-404 Questions and answers with ExamsMirror

The CRC is calculated over the MAC Header and Frame Body only. The CRC (Cyclic Redundancy Check) is a 32-bit value that is used for error detection in wireless transmissions. The CRC is calculated over the MAC Header and Frame Body of a PSDU, which are the parts of the data unit that contain information such as source and destination addresses, frame type, frame control, sequence number, payload, etc. The CRC is appended to the end of the PSDU as a FCS (Frame Check Sequence) field. The CRC is not calculated over the PHY Header or PHY Preamble, which are parts of the PPDU that contain information such as modulation, coding, data rate, etc. The PHY Header and PHY Preamble are added or removed by the PHY layer during the conversion between PSDU and PPDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

The To DS and From DS flags should be set to 0 in an Association Response frame. An Association Response frame is a type of management frame that is transmitted by an AP to accept or reject an association request from a STA. The To DS (To Distribution System) and From DS (From Distribution System) flags are two bits in the Frame Control field of the MAC header that indicate whether a frame is destined for or originated from the DS (Distribution System), which is a system that connects multiple BSSs together. The To DS and From DS flags can have four possible combinations: 00, 01, 10, or 11. For an Association Response frame, which is sent from an AP to a STA within a BSS, both flags should be set to 0. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 121-122

The beamformee transmits a Feedback Matrix within the Compressed Beamforming frame to the beamformer. The Feedback Matrix contains information about the channel state between the beamformee and each spatial stream of the beamformer. This information is used by the beamformer to adjust its transmit weights and optimize its signal for the beamformee34. References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 11: 802.11n/ac/ax PHYsical Layer Frame Exchanges, page 4033; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 11: 802.11n/ac/ax PHYsical Layer Frame Exchanges, page 4064.

The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

A PHY header is added to the PSDU at the PHY layer. A PHY header is a part of the PPDU that contains information such as modulation, coding, and data rate. The PHY header is added by the PHY layer when it converts a PSDU to a PPDU for transmission, or removed by the PHY layer when it converts a PPDU to a PSDU for reception. The other layers do not add or remove a PHY header. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

If the SSID element has a length of 0 in a Beacon frame decode, it means that the beacon is from a BSS configured to hide the SSID. The SSID element is a part of the Beacon frame that contains the name or identifier of the BSS. The SSID element has two fields: length and value. The length field indicates how many bytes are used for the value field, which contains the actual SSID string. If the length field is 0, it means that there is no value field or SSID string in the element. This is a common technique used by some APs to hide their SSID from passive scanning clients or potential attackers. However, this technique does not provide much security, as there are other ways to discover or reveal the hidden SSID, such as active scanning or capturing probe response or association frames. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 122-123

The best way to test the theory of microwave interference from the New York office is to use a remote spectrum analyzer. By placing one of the London APs into spectrum analyzer mode, you can capture and analyze the RF spectrum in the London office over lunch time. You can then look for any signs of microwave interference, such as high duty cycle, high amplitude, or frequency hopping on the 2.4 GHz band. This method does not require any physical access tothe microwave or any changes to its frequency. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 64

A capture visualization tool is a software application that can open a packet capture file and display various graphs, charts, tables, and statistics that illustrate the characteristics and behavior of the wireless network. A capture visualization tool can help a network administrator with little knowledge of 802.11 protocols to evaluate the overall health and performance of their wireless network by providing a visual and intuitive representation of the captured data. A spectrum analyzer is a hardware device that measures the radio frequency signals in a given frequency range and displays their amplitude, frequency, and modulation. A spectrum analyzer can help identify sources of interference and noise in the wireless environment, but it cannot open a packet capture file. Python is a programming language that can be used to write scripts or applications that manipulate or analyze packet capture files, but it requires coding skills and knowledge of 802.11 protocols. A WLAN scanner is a software application that scans for available wireless networks and displays information such as SSID, BSSID, channel, signal strength, security type, and vendor. A WLAN scanner can help discover wireless networks and their basic parameters, but it cannot open a packet capture file345 References:

CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 63

CWAP-404 Objectives, Section 2.5: Use capture visualization tools

CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 117

CWAP-404 Objectives, Section 4.1: Use spectrum analysis tools

CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 33

CWAP-404 Objectives, Section 2.2: Analyze field values

The device finder is a common feature of a spectrum analyzer that helps locate a non-802.11 interference source. The device finder uses a directional antenna to measure the signal strength of a specific frequency or signal source. By pointing the antenna in different directions, the device finder can indicate the direction and distance of the interference source. The device finder can also filter out other signals that are not related to the interference source. The other options are not correct, as they do not help locate a non-802.11 interference source. Max hold and min hold are features that show the maximum and minimum RF power levels over time,respectively. Location filter is a feature that filters out signals that are not from a specific location or area. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 77-78

The statement that the Frame Control field contains subfields, and some 1-bit flags is true. The Frame Control field is a 2-byte field in the MAC header that contains information about the type, subtype, and characteristics of a frame. The Frame Control field is divided into several subfields, each with a specific function and length. Some of these subfields are 1-bit flags, which can be set to 0 or 1 to indicate a certain condition or status. For example, the To DS and From DS subfields are 1-bit flags that indicate whether a frame is destined for or originated from the DS (Distribution System). The other statements are not true, as they do not describe the Frame Control field correctly. All types of frames (management, control, and data) have a Frame Control field, not just control frames. The Frame Control field is not used to communicate the duration value, which is a separate field in the MAC header. The Frame Control field is not always set to 0, as it varies depending on the type, subtype, and characteristics of each frame. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 113-114