Weekend Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = simple70

Home
EMC
Implementation Engineer
E20-260
VPLEX Specialist Exam for Implementation Engineers Questions and Answers

Pass the EMC Implementation Engineer E20-260 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.

Exam E20-260 Premium Access

View all detail and faqs for the E20-260 exam

Go to Exam

479 Students Passed

92% Average Score

94% Same Questions

Viewing page 1 out of 7 pages

Viewing questions 1-10 out of questions

Questions # 1:

Refer to the exhibit.

Question # 1

A customer has not followed EMC best practices when cabling their VS2 VPLEX engine. You are asked how to re-cable the engine to adhere to best practices. What is your response?

Options:

Swap port 00 with port 01 of module A1-BE and B1-BE.

Swap port 02 with port 03 of module A0-FE and B0-FE.

Swap port 00 with port 01 of module A0-FE and B0-FE.

Swap port 02 with port 03 of module A1-BE and B1-BE.

Answer

Questions # 2:

When creating logging and metadata volumes, which LUN requirement applies to both?

Options:

Array LUNs must be zeroed-out.

Array LUNs must be RAID-need a number here

Array LUNs must be thin.

Array LUNs must be RAID-need a number here

Answer

Questions # 3:

What information is required to configure ESRS for VPLEX?

Options:

VPLEX model type

Top Level Assembly

Site ID

IP address of the Management Server public port

Top Level Assembly

Site ID

IP address of the Management Server public port

VPLEX Configuration (1, 2 or 4 Engines)

VPLEX model type

Top Level Assembly

Primary customer contact

IP address of the Management Server public port

VPLEX model type

Site ID

IP address of the Management Server public port

Primary Customer contact

Answer

Questions # 4:

Which information is required to configure ESRS for VPLEX?

Options:

VPLEX model type Top Level Assembly Site ID IP address of the Management Server public port

B/Top Level Assembly Site ID IP address of the Management Server public port Configuration (1, 2 or 4 Engines)

VPLEX model type Level Assembly customer contact IP address of the Management Server public port

VPLEX model type Site ID IP address of the Management Server public port Primary Customer contact

Answer

Questions # 5:

What is an EMC best practice for fault tolerance when zoning a VPLEX Metro together over Fibre Channel for successful communication between the sites?

Options:

Zone each WAN-COM port to all WAN-COM ports in the other fabric.

Zone all WAN-COM ports to each other in both SAN fabrics within a single zone.

Zone each WAN-COM port to all WAN-COM ports in the other fabric.

Zone one Local-COM port to all WAN-COM ports in the other fabric for VPLEX Witness.

Zone all WAN-COM ports to each other in both SAN fabrics within a single zone.

Zone one Local-COM port to all WAN-COM ports in the other fabric for VPLEX Witness.

Answer

Questions # 6:

What is the role of the port with the WWN 5000144270061010 on a VS2 engine?

Options:

Back-end

Front-end

Local-COM

WAN-COM

Answer

Questions # 7:

Refer to the exhibit.

Question # 7

The customer has not followed EMC best practices when cabling their VS2 VPLEX engine. You are asked how to re-cable the engine to adhere to best practices. What is your response?

Options:

Swap port 00 with port 01 of module A0-FE and B0-FE.

Swap port 00 with port 01 of module A1-BE and B1-BE.

Swap port 02 with port 03 of module A0-FE and B0-FE.

Swap port 02 with port 03 of module A1-BE and B1-BE.

Answer

Questions # 8:

Refer to the exhibit.

Question # 8

During a short power disruption to cluster 2, director-2-1-A failed. Power was restored after 5 minutes. In examining the output of the vault status command, you note that cluster-2's status reads "Cluster is not vaulting/unvaulting".

Why did this message appear?