Pass the Oracle Exadata 1z0-902 Questions and answers with ExamsMirror

According to Oracle’s documentation1, the client network on Exadata X9M-2 Database Server is used for client access to the database servers using Single Client Access Name (SCAN) and Oracle RAC Virtual IP (VIP) addresses. To verify that the client network is available via both client switches, you can use the command:

cat /proc/net/bonding/bondeth0

This command displays information about the bondeth0 interface, which is used for the client network on Exadata X9M-2 Database Server2. You can check if both interfaces (eth0 and eth1) are active and connected to different switches3.

According to the Oracle Exadata Database Machine X9M-2 Data Sheet1, each PDU has two power input cables that can be connected to separate power sources for redundancy. However, if only one power source is available per PDU, then a single cable can be used to provide sufficient power for normal operation.

https://www.oracle.com/a/ocom/docs/engineered-systems/exadata/exadata-x9m-2-ds.pdf

Once the physical disk has been replaced, you will need to create a new celldisk and griddisks on the replaced physical disk. After the griddisks have been dropped from the associated ASM diskgroups, you can then add the griddisks back into the ASM diskgroup they used to be a member of and rebalance the data on the effected griddisks. Finally, you should verify that the griddisks located on the physical disk have been successfully dropped from the associated ASM diskgroups.

The dbmcli -e "LIST IBPORT DETAIL" command is not valid on Exadata X9M. According to the Oracle Exadata Database Machine X9M Implementation Essentials Official Text Book [1][2], this command is only valid on Exadata X3 and X4 models. The other three commands are valid on Exadata X9M.

https://forums.oracle.com/ords/apexds/map/tech/apps-infra/discussion/4342715/monitoring-roce-performance

In order to monitor all components of this multirack configuration, Enterprise Manager agents must be deployed on at least two storage servers in both racks and all database servers in both racks. This is according to the Oracle Exadata Database Machine X9M Implementation Essentials official text book [1], in which it states "To monitor all components of the multirack configuration, you must deploy agents on all database servers and at least two storage servers in each rack" (page 6-15).

For Exadata systems, hardware monitoring for components like the motherboard, memory, power, fans, and network cards on the database nodes is managed through the Integrated Lights Out Manager (ILOM). The ILOM provides built-in thresholds and sensor readings that are automatically recognized by Oracle Enterprise Manager.

These thresholds and alerts are already configured within ILOM for Exadata components, ensuring seamless integration with Enterprise Manager for alerting and monitoring purposes​.

Enterprise Manager uses these pre-set ILOM thresholds and does not require additional configuration for monitoring hardware components. Therefore, administrators benefit from preset alerting mechanisms that are sufficient for comprehensive hardware status visibility​.

High Capacity (HC) Storage Server: The Exadata X9M-2 HC storage server is configured with a combination of hard disks and flash memory, providing a balance of storage capacity and performance.

It includes 12 x 18 TB hard disk drives, which totals 216 TB of raw disk capacity​.

For flash storage, it has 4 x 6.4 TB PCIe flash cards totaling 25.6 TB of flash storage. This configuration uses NVMe Flash Accelerator F680 cards optimized for database caching​​.

The persistent memory in the HC server totals 1.5 TB, enhancing performance for OLTP (Online Transaction Processing) workloads by providing ultra-fast access speeds compared to traditional flash storage​.

Extreme Flash (EF) Storage Server: The EF storage server in the Exadata X9M-2 model is an all-flash storage server designed for high IOPS and low latency, making it ideal for performance-intensive workloads.

This configuration contains 8 x 6.4 TB PCIe flash cards, providing a raw capacity of 51.2 TB of high-performance flash storage​.

In terms of persistent memory, it includes 756 GB of Intel Optane Persistent Memory. This enhances flash storage performance by offloading data processing directly to persistent memory​​.

The Exadata X9M-2 storage configurations—both HC and EF—are optimized for different workload requirements. The HC configuration caters to larger datasets needing high storage capacity, while the EF configuration is designed for workloads requiring high throughput and minimal latency.

Exadata Database Machine is a pre-configured and pre-tuned hardware and software system designed to run Oracle Database, it can be installed on raised floor environments, but also on concrete or tile floors

Oracle Exadata Database Machine X9M Implementation Essentials states that Exadata racks are designed to be installed on flat surfaces, not raised floor environments. It is not required to install the rack on raised floor environments. Additionally, the other options listed are all requirements for validating, receiving, unpacking, and planning access route and space requirements for Exadata Database Machine. (Source: Oracle Exadata Database Machine X9M Implementation Essentials, page 41)

https://docs.oracle.com/en/engineered-systems/exadata-database-machine/dbmin/index.html

For a non-virtual deployment of Oracle Exadata with a single cluster:

Single Client Access Name (SCAN) Listeners: By default, three SCAN listeners are configured on the RDMA over Converged Ethernet (RoCE) network. This setup allows for load balancing and high availability of incoming client connections across the cluster nodes​.

Oracle Cluster Registry (OCR) Multiplexing: The OCR is typically stored in multiple locations within the disk groups to enhance reliability and fault tolerance. On Exadata, the OCR is multiplexed across the DATA and RECO disk groups for enhanced resilience​.

ora.diskmon Resource: This is an essential component of Oracle Clusterware, responsible for monitoring and managing disk-related cluster resources. It is always enabled and kept online by Oracle Clusterware on Exadata systems​.

In an Exadata environment, the path of communication for SNMP traps involves:

Management Server (MS) Process to EM Agent: Alerts related to the storage server are generated by the MS process, which then forwards SNMP traps directly to the Enterprise Manager agent, allowing centralized monitoring and alert management​.

ILOM to EM Agent: The ILOM on each Exadata storage server can independently send SNMP traps to the EM agent, providing additional hardware-level monitoring and alerting capabilities .

These pathways ensure that alerts from both hardware and software layers reach Enterprise Manager efficiently, supporting proactive management and rapid response to system issues.