Weekend Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = simple70

Pass the Brocade Converged 150-820 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.
Exam 150-820 Premium Access

View all detail and faqs for the 150-820 exam


346 Students Passed

86% Average Score

90% Same Questions
Viewing page 1 out of 6 pages
Viewing questions 1-10 out of questions
Questions # 1:

Exhibit:

sw0(conf-if-te-0/5)# channel-group 100 mode active type standard

%%Error: A switchport or a router port cannot be aggregated

Exhibit:

Referring to the exhibit, what is the cause of the error when applying a port channel to an interface?

Options:

A.

A routing protocol is configured in the port channel.

B.

Access mode is not supported with link aggregation.

C.

Switchport is configured in the port channel.

D.

Switchport is configured on the interface.

Questions # 2:

During a network outage, several RBridges in VCS Logical Chassis mode were disconnected from the rest of the network. During this time, some configuration changes were made to those switches.

When the network connection between the separated switches is repaired, what will occur?

Options:

A.

The fabric configuration will merge.

B.

The configuration of the separated fabric will be overwritten.

C.

The configuration of the main fabric will be overwritten.

D.

The fabric configurations will not merge.

Questions # 3:

Your customer would like to control a Brocade VCS Fabric consisting of four Brocade VDX 6740s by using SSH to the same address on the principal switch in the fabric.

Which two attributes should be configured to accomplish this? (Choose two.)

Options:

A.

Assign management IP addresses to the RBridges in the fabric.

B.

Assign the chassis virtual IP to one RBridge.

C.

Assign the VCS virtual IP to the Brocade VCS Fabric.

D.

Assign the mcast root to one RBridge.

Questions # 4:

You have implemented flow-based sFlow in your Brocade VCS Fabric by enabling sFlow globally on each Brocade VDX. You are not receiving any statistics in your sFlow collector from these devices.

What must happen to start collecting data?

Options:

A.

Enable sFlow on ISLs.

B.

Enable sFlow on individual interfaces.

C.

Enable sFlow on port channels.

D.

Enable sFlow on vLAGS.

Questions # 5:

A principal RBridge fails.

What happens to the VCS virtual IP address?

Options:

A.

The newly elected principal switch's management IP becomes the VCS virtual IP address.

B.

The switch with the highest WWN owns the VCS virtual IP address.

C.

The switch with the lowest MAC management IP address becomes the VCS virtual IP address.

D.

The existing VCS virtual IP address will be bound to the newly elected principal switch.

Questions # 6:

Which two port profile attributes would be assigned before applying the port profile to an interface? (Choose two.)

Options:

A.

port speed

B.

VLAN configuration

C.

port duplex

D.

security ACLs

Questions # 7:

A customer implements a fault tolerant network and has requested that the switches in the data center support multiple management modules.

Which two Brocade VDX switches would you recommend for this requirement? (Choose two.)

Options:

A.

VDX 6710

B.

VDX 8770-4

C.

VDX 6730-76

D.

VDX 8770-8

Questions # 8:

Your Ethernet fabric is running NOS 4.1.1 on two Brocade VDX 8770s and four Brocade VDX 6730s in fabric cluster mode. You are required to deploy servers connected to the VDX switches that will communicate with FC targets. Layer 3 features must be deployed in the design.

Which two licenses are required? (Choose two.)

Options:

A.

a VCS Fabric license on each switch

B.

an FCoE base license on each switch

C.

a Layer 3 license on each VDX 6740

D.

a Layer 3 license on each VDX 8770

Questions # 9:

You are required to deploy servers with a single adapter that are attached to your Brocade VDX 6730 running in Access Gateway mode that will communicate with FC SAN attached storage.

Which statement is true?

Options:

A.

LSAN zones are required in the FC SAN.

B.

LSAN zones are required in the Ethernet fabric.

C.

Traditional FC zones are required in the Ethernet fabric.

D.

Traditional FC zones are required in the FC SAN.

Questions # 10:

You have three Brocade VCS Fabrics linked together and have enabled ELD.

Question # 10

Referring to the exhibit, which link would be blocked?

Options:

A.

the link between a1 and b1

B.

the link between b2 and c2

C.

the link between a2 and c1

D.

the link between a3 and a4

Viewing page 1 out of 6 pages
Viewing questions 1-10 out of questions
TOP CODES

TOP CODES

Top selling exam codes in the certification world, popular, in demand and updated to help you pass on the first try.