Pass the Cisco CCNP Data Center 300-615 Questions and answers with ExamsMirror

Manually configure DNS in the Guest shell, even if it is claimed on the Cisco Nexus switch through DHCP is the required fix because the automation failure is caused by execution context, syntax, or resource state around Guest Shell, Cisco Nexus. On Cisco Nexus switches, automation is not a single feature; EEM policies, CLI actions, Guest Shell Linux commands, REST payloads, and scheduled jobs are evaluated by different subsystems. A script can fail even while the switch itself has connectivity or the command works interactively. The selected answer supplies the missing requirement, such as the correct event/action, DNS or resource setting, API URI, payload format, feature enablement, or reboot needed for a Guest Shell change to take effect. The other choices address adjacent features but do not satisfy the failing subsystem. After applying the fix, the engineer should verify the policy registration, job result, API response code, or Guest Shell runtime state and confirm that the intended command is no longer blocked or silently ignored.

Enable the peer-gateway feature is correct because the failure is an operations-plane condition involving HSRP. In Cisco data center products, management functions depend on more than IP connectivity. AAA servers must return the correct attributes, RBAC must map users to the correct security domain or role, certificates must be trusted and valid for the access method, and firmware or registration workflows must satisfy documented prerequisites such as NTP and required ports. The selected answer corrects that dependency. The distractors are not root-cause fixes because they either target a different subsystem or change a setting that would not influence the observed login, registration, warning, or fault. After the change, validation should include a successful login or registration test, review of the audit/fault record, and confirmation that the expected administrative scope is enforced. That approach matches Cisco operational troubleshooting for DCIT environments. The final check is to document the before-and-after state so the remediation is tied to a repeatable Cisco troubleshooting symptom rather than an assumed fix.

Configure the NVE interfaces to be Up on both switches; Configure the same VNI to multicast group mapping is the valid corrective action because the failure described is a protocol or fabric state problem, not a generic connectivity issue. For vPC, VXLAN, EVPN, NVE, VNI, Cisco troubleshooting expects the engineer to compare both endpoints of the relationship: vPC peers must agree on consistency parameters, HSRP peers must exchange hellos in the same VLAN and version context, OSPF/BGP peers must match the attributes required for stable adjacency, and VXLAN EVPN must advertise the correct host or prefix information. The selected option restores that required state. The other options either operate on the wrong layer, change a value that is not used to form the relationship, or would make the peer relationship less deterministic. A clean validation is to inspect the control-plane table first, then verify the forwarding table, and finally test end-to-end traffic. This is the Cisco-preferred approach because it avoids random changes and confirms that the fabric is forwarding based on correct protocol state.

Reregister the site in the Nexus Dashboard GUI is correct because the failure is an operations-plane condition involving ACI, APIC, Nexus Dashboard, Cisco Nexus. In Cisco data center products, management functions depend on more than IP connectivity. AAA servers must return the correct attributes, RBAC must map users to the correct security domain or role, certificates must be trusted and valid for the access method, and firmware or registration workflows must satisfy documented prerequisites such as NTP and required ports. The selected answer corrects that dependency. The distractors are not root-cause fixes because they either target a different subsystem or change a setting that would not influence the observed login, registration, warning, or fault. After the change, validation should include a successful login or registration test, review of the audit/fault record, and confirmation that the expected administrative scope is enforced. That approach matches Cisco operational troubleshooting for DCIT environments.

Add event-default as a second action of the EEM script is the required fix because the automation failure is caused by execution context, syntax, or resource state around EEM. On Cisco Nexus switches, automation is not a single feature; EEM policies, CLI actions, Guest Shell Linux commands, REST payloads, and scheduled jobs are evaluated by different subsystems. A script can fail even while the switch itself has connectivity or the command works interactively. The selected answer supplies the missing requirement, such as the correct event/action, DNS or resource setting, API URI, payload format, feature enablement, or reboot needed for a Guest Shell change to take effect. The other choices address adjacent features but do not satisfy the failing subsystem. After applying the fix, the engineer should verify the policy registration, job result, API response code, or Guest Shell runtime state and confirm that the intended command is no longer blocked or silently ignored.

action 2.0 event-default is the required fix because the automation failure is caused by execution context, syntax, or resource state around EEM. On Cisco Nexus switches, automation is not a single feature; EEM policies, CLI actions, Guest Shell Linux commands, REST payloads, and scheduled jobs are evaluated by different subsystems. A script can fail even while the switch itself has connectivity or the command works interactively. The selected answer supplies the missing requirement, such as the correct event/action, DNS or resource setting, API URI, payload format, feature enablement, or reboot needed for a Guest Shell change to take effect. The other choices address adjacent features but do not satisfy the failing subsystem. After applying the fix, the engineer should verify the policy registration, job result, API response code, or Guest Shell runtime state and confirm that the intended command is no longer blocked or silently ignored.

Cisco troubleshooting logic supports On VTEP1, associate VNI 50000 to Test Telco VRFOn VTEP4, associate VNI 50000 to Test Telco VRF as the required fix. In this question the symptoms point to VXLAN, VNI, and the defect is best handled by correcting the exact control-plane or consistency condition. Nexus platforms can show interfaces or peers as configured while still refusing to forward traffic if a vPC Type-1 parameter, VLAN allowance, MTU, HSRP version, EVPN route, or routing attribute is wrong. Cisco methodology is to avoid broad resets unless the state machine is stuck; instead, correct the mismatched parameter and verify that the resulting operational state becomes stable. The other choices do not remove the root cause, or they modify a setting that is not used by the failing protocol exchange. After the change, the engineer should review the peer status, route or MAC table, and counters for drops or inconsistency messages. That sequence proves that the network fabric is fixed, not merely restarted.

The answer is Enable LLDP because Cisco Nexus and ACI forwarding depends on exact agreement between the devices participating in the feature. The scenario references DCBX, LLDP, Cisco Nexus; those technologies fail in predictable ways when required parameters do not match or when the required control-plane advertisement is absent. In DCIT troubleshooting, the engineer should identify the failed dependency, correct that dependency, and then verify the operational table that proves the fix. For example, vPC and EVPN checks focus on consistency, VNI/VRF bindings, peer-gateway behavior, and host-route advertisement; routing checks focus on neighbor state, MTU, timers, authentication, next-hop, and route preference. The selected answer addresses the dependency that blocks forwarding. The distractors are plausible because they touch related features, but they do not resolve the specific failure condition. Post-change validation should include protocol state, learned endpoint or route entries, and a traffic test across the affected path.

The correct answer is Option A. Cisco MDS and Nexus SAN troubleshooting is driven by fabric state: the host and target must be in the correct VSAN, must complete FLOGI/PLOGI where applicable, and must be permitted by active zoning, fcdomain, FSPF, NPV/NPIV, or port-security policy. This question focuses on MDS, VSAN, port security, so the selected action fixes the dependency that prevents the initiator, target, or inter-switch link from becoming usable. Cisco documentation emphasizes checking VSAN membership, active zonesets, correct port mode, fabric binding, device-alias consistency, and the relevant FC databases before changing unrelated server settings. The distractors either target a different database, use the wrong port role, or would not cause the observed Fibre Channel state to change. After the fix, the engineer should confirm the interface state, FLOGI database, name-server entries, zoneset activation, and successful initiator-to-target reachability with tools such as fcping or fabric show commands.

Use a browser that supports keys of 2048 bits resolves the issue because the root cause belongs to the management and operations layer around ACI, APIC, certificate. Cisco DCIT troubleshooting requires identifying whether the issue is caused by AAA, RBAC, certificate trust, SNMP access, firmware workflow, license/feature state, or lifecycle registration. The selected option changes the specific item that the platform checks before allowing the operation to complete. The incorrect options either touch data-plane forwarding, change an attribute that is not evaluated for the task, or would create unnecessary disruption. A correct operational fix should be measured by the management result, not just by interface status. The engineer should repeat the login, registration, certificate access, or fault workflow, then verify the audit log and effective permissions. That method confirms the platform is behaving as Cisco expects and that the correction is durable across subsequent operations.