Pass the Cisco Meraki Solutions Specialist 500-220 Questions and answers with ExamsMirror

https://documentation.meraki.com/MV/Advanced_Configuration/Scheduled_Recording

By default, the Meraki security camera's will record continuously 24/7. In some situations, certain times of day are not allowed to be recorded. Scheduled recording covers this requirement as well as improve the video retention capabilities of the camera.

If you only need traffic statistics from your spoke site clients then you only need to enable insight on the spoke network as the hub site will not gather data for remote sites. https://community.meraki.com/t5/Wireless-LAN/Meraki-Insight-Licensing/m-p/152684

A license is only required for those networks where Meraki Insight functionality is desired. One license is required per network, regardless of whether that network has a single MX or HA pair. Licenses can be moved between networks, but historical data for the old network will be lost. https://meraki.cisco.com/lib/pdf/meraki_datasheet_mi.pdf

iOS devices that are using Apple's Device Enrollment Program (DEP) can be supervised and enrolled over-the-air anytime they are factory reset. DEP is the best way to permanently force your devices to be owned and managed by your organization, and it is important to assign your DEP settings properly before deployment. https://documentation.meraki.com/SM/Device_Enrollment/Enrolling_and_Supervising_iOS_Devices_using_Apple_Configurator_2.5_or_Later#:~:text=DEP%20is%20the%20best%20way,DEP%20settings%20properly%20before%20deployment .

Routed Mode:

This mode is the default mode of operation

This mode is generally also the default gateway for devices on the LAN

Client traffic to the internet has the source IP rewritten to match the WAN IP of the appliance

DHCP services can be configured on the MX appliance

Passthrough Mode:

The MX appliance acts as a layer 2 bridge

VLANs cannot be configured

No address translation is provided

This mode is not recommended at the network perimeter

This question is related to the topic of MX Addressing and VLANs in the Cisco Meraki documentation. You can find more information about this topic in the MX Addressing and VLANs article or the General MX Best Practices page.

See Behavior - Firmware MX 15.11 or Lower section For MXs running firmware MX15.11 or below, the source IP that MX uses while pinging a destination is the MX IP of highest VLAN ID. If the destination is across a VPN, the MX uses the MX IP of highest VLAN ID participating in VPN. For MXs running firmware MX 15.12+, additional ping options have been added to the live tool. The ping tool now has a drop down to select the source IP address for pinging destinations from the MX. https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Using_the_Ping_Live_Tool

https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MX_Security_and_SD-WAN/MX_Templates_Best_Practices#:~:text=policy%2C%20choose%20Save-,Local%20Overrides,will%20override%20the%20template%20configuration .

Quote from referred documentation-Link: Loss and latency will be determined over the configured IP address under Security and SD-WAN > SD-WAN and Traffic Shaping > Uplink Statistics. If no IP is configured, these values will be measured against 8.8.8.8 by default. On the WAN Health page, all the configured IP address statistics can be reviewed by changing the destination under the "Ping Destination" column.

https://documentation.meraki.com/MI/MI_WAN_Health#:~:text=Current%20loss%20and%20latency%20statistics,address%20is%20set%20to%208.8 .

When a rogue access point is contained, clients will be unable to connect to the rogue AP. Additionally, any currently associated clients will lose their connection to the rogue AP. https://documentation.meraki.com/MR/Monitoring_and_Reporting/Air_Marshal

More hardware devices than device licenses: An organization needs to have enough device licenses to cover all the hardware devices in its network. A device license is consumed by each device that is added to the network. If the number of devices exceeds the number of licenses, the organization will be out of license and will lose access to some features and support until it purchases more licenses or removes some devices4.

Expired device license: A device license has an expiration date that depends on the license term purchased by the organization. If a device license expires, it will no longer be valid and will not count towards the license limit. The organization will need to renew the expired license or purchase a new one to avoid being out of license4.

The correct answer is B and D. These are the two methods of targeting and applying management profiles to System Manager clients, according to the [System Manager: Getting Started] article. The article explains that:

Defining the scope: This method allows you to target devices based on their network, tag, or owner. You can define the scope of a profile from the Systems Manager > Manage > Settings page or from the Systems Manager > Monitor > Overview page.

Using device tags: This method allows you to target devices based on their attributes, such as OS, model, location, or user. You can use device tags to create dynamic groups of devices that share common characteristics. You can apply device tags from the Systems Manager > Monitor > Devices page or from the Systems Manager > Manage > Tags page.