Pass the EMC DCE DEE-1111 Questions and answers with ExamsMirror

 When maintenance tasks at the R1 data center require the array to be offline, a Swap operation should be executed on the Metro RDF pairs. This operation allows for a planned outage without affecting application I/O by swapping the roles of R1 and R2 devices. 

The maximum retention period for the SLO Compliance Report is 6 months. This means that data older than 6 months will not be available in the report

R11 devices are included in a Cascaded SRDF environment. In a cascaded SRDF configuration, the R1 device at the primary site is paired with an R11 device at the secondary site, which is then paired with an R2 device at the tertiary site2. References: NDM overview | Dell EMC PowerMax and VMAX: Non-Disruptive Migration Best Practices and Operational Guide | Dell Technologies Info Hub

Fast Write is a Dell EMC technology that improves Fibre Channel (FC) replication between sites in a SRDF/S configuration. When a write I/O is issued by the host to the R1 device, SRDF with Fast Write acknowledges the write to the host as soon as the data is stored in the R1’s cache and transmitted to the R2’s cache. This results in reduced latency and improved performance for FC replication between sites.

https://www.delltechnologies.com/asset/en-us/products/storage/industry-market/h17118_dell_emc_powermax_family_overview.pdf

https://infohub.delltechnologies.com/l/dell-emc-powermax-and-vmax-all-flash-srdf-metro-overview-and-best-practices-1/srdf-metro-overview/

The steps in sequence as part of key management for a drive failure on a PowerMax array are as follows:

Spare drive invoked against failed drive. This step involves the system automatically selecting a spare drive and starting the sparing operation to rebuild the data from the failed drive.The spare drive is encrypted with a temporary key that is stored in the embedded key manager.1

1st entry in audit log.This step involves the system logging the sparing operation and the temporary key generation in the audit log, which records all key management activities and events.1

Sparing operation is completed. This step involves the system completing the data rebuild and marking the spare drive as a permanent replacement for the failed drive.The spare drive becomes part of the RAID group and inherits the same properties as the failed drive.1

Key is deleted from the repository when failed drive is removed. This step involves the system deleting the Data Encryption Key (DEK) of the failed drive from the embedded key manager when the failed drive is physically removed from the array.The DEK is a unique 256-bit AES-XTS key that is used to encrypt and decrypt data on each drive.1

2nd entry in audit log.This step involves the system logging the DEK deletion and the failed drive removal in the audit log.1

Key is generated for the replacement drive when installed. This step involves the system generating a new DEK for the replacement drive when it is installed in the array.The new DEK is stored in the embedded key manager and used to encrypt and decrypt data on the replacement drive.1

References:

Dell EMC PowerMax and VMAX All Flash: Data at Rest Encryption

The symaudit -list command is used to display audit records for SYMCLI commands. The exhibit shows the output of the symauth -list command, which displays the user groups and access types defined for SYMCLI commands. The output shows that there are two user groups: AdminGrp and EmcMgmtGrp. The AdminGrp group has ADMINRD access type, which means that users in this group can run any SYMCLI command with read-only access. The EmcMgmtGrp group has BASECONTROL access type, which means that users in this group can run only a subset of SYMCLI commands with read/write access. However, the output also shows that there are two exceptions for specific users: Beth and Frank. Beth has ADMINRD access type for all commands, which overrides her membership in EmcMgmtGrp group. Frank has BASECONTROL access type for all commands, which overrides his membership in AdminGrp group. Therefore, the only user who has access to run the symaudit -list command based on the symauth output shown in the exhibit is Beth, since she has ADMINRD access type for all commands2