Weekend Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = simple70

Home
EMC
EMC Certification
DES-1241
Specialist - Platform Engineer PowerStore Exam Questions and Answers

Pass the EMC Certification DES-1241 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.

Exam DES-1241 Premium Access

View all detail and faqs for the DES-1241 exam

Go to Exam

434 Students Passed

94% Average Score

94% Same Questions

Viewing page 1 out of 3 pages

Viewing questions 1-10 out of questions

Questions # 1:

Which account credentials are needed to run diagnostic commands?

Options:

root

service

console

admin

Answer

Questions # 2:

Refer to the exhibit.

Question # 2

What type of cable is used for the ToR switch configuration shown for the S5248F-ON switches?

Options:

10 GigE Cat 6 Ethernet RJ-45

25 GigE Twinax

100 GigE QSFP28

10 GigE SFP optical cable

Answer

Explanation

[Reference: https://www.dellemc.com/resources/en-us/asset/technical-guides-support-information/solutions/ h18242-ready-stack-powerstore-dg.pdf?dgc=SM&cid=170850&lid=spr3492306896&linkId=93885839, ]

Questions # 3:

Which component is a CRU?

Options:

Base enclosure

Expansion enclosure

Battery Backup Unit

Nodes

Answer

Explanation

https://www.dellemc.com/content/dam/digitalassets/active/en/unauth/manual-warranty-informations/h4276-emc-prod-warranty-maint-table.pdf

Questions # 4:

What describes Dell EMC PowerStore X front-end cabling?

Options:

Uses internal VMware virtual switching and does not require a management network

Storage and management use the same LACP bonded cable connection

Uses VLTi data switch interconnectivity to support vMotion networks

Management and discovery use the same cables and connections as storage

Answer

Explanation

"For PowerStore T model appliances, the individual ports within the system bond could be running in active/active mode or active/passive mode. This state depends on whether Link Aggregation Control Protocol (LACP) has been configured on the network switches. To ensure best resiliency and network performance, it is recommended to enable LACP on the network. For more information about configuring LACP for a PowerStore T model appliance, see the document PowerStore Guide for PowerStore T Models on the PowerStore Info Hub. For PowerStore X model appliances, there is no system bond and no LACP configuration is needed because the link aggregation and failover is handled by the virtual switches within the VMware hypervisor. "

Questions # 5:

The “svc_rescue_state list” shows a node in service mode. How can the node be returned to normal mode?

Options:

svc_rescue_state normal

svc_rescue_state clear

svc_rescue_state exit

svc_rescue_state quit

Answer

Questions # 6:

What describes Dell EMC PowerStore X power down?

Options:

PowerStore X node, appliance, or cluster power down is done entirely with vCenter server commands

Powering down a PowerStore X node, appliance, or cluster is done in the same manner as a PowerStore T

PowerStore X node, appliance, or cluster power down utilizes the VSi plugin to perform the needed vCenter server operations

Powering down a PowerStore X node, appliance, or cluster requires additional vCenter server commands

Answer

Questions # 7:

How is a defective embedded module displayed in Dell EMC PowerStore Manager?

Options:

Orange with an empty state

Orange with a faulted state

Blue with a faulted state

Blue with an empty state

Answer

Questions # 8:

Which type of device is supported in expansion enclosures?

Options:

NVMe SCM

NVMe SSD

NVMe NVRAM

SAS SSD

Answer

Questions # 9:

What is a step in configuring the ToR data switches for a Dell EMC PowerStore X?

Options:

Configure a port for the discovery laptop

Create VLANs for NAS servers

Create node A port-channel

Configure LACP uplink to management switch

Answer

Explanation

[Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-ntwk-cfg/configure- port-interfaces-for-powerstore-x-model-node-connectivity?guid=guid-ef6b40ef-82a3-4ebf-99bf- a7bea8d6a586&lang=en-us, ]

Questions # 10:

Refer to the exhibit.

Question # 10