Pass the Ericsson Certified Associate ECP-206 Questions and answers with ExamsMirror

To differentiate traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone, an operator can use the following three fields:

Traffic Class (TC): This is a 3-bit field in the MPLS label that can be used to indicate the priority or class of service (CoS) of the packet. The TC field can be mapped to the DSCP field in the IP header or the PCP field in the Ethernet header. The TC field can be used by MPLS routers to apply different per-hop behaviors (PHBs) such as queuing, scheduling, and dropping policies to different traffic classes12.

DSCP: This is a 6-bit field in the IP header that can be used to mark packets according to the differentiated services (DiffServ) model. The DSCP field can indicate the per-hop behavior (PHB) that the packet should receive at each router along its path. The DSCP field can be mapped to the TC field in the MPLS label or the PCP field in the Ethernet header. The DSCP field can be used by IP routers to provide QoS for different traffic types34.

PCP: This is a 3-bit field in the Ethernet header that can be used to mark packets according to the IEEE 802.1Q standard. The PCP field can indicate the priority or class of service (CoS) of the packet on an Ethernet LAN. The PCP field can be mapped to the TC field in the MPLS label or the DSCP field in the IP header. The PCP field can be used by Ethernet switches to provide QoS for different traffic types56.

References: MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering, MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering Configuration Guide, Differentiated services - Wikipedia, DSCP and Precedence Values - Cisco, 802.1Q VLAN IDs and Ethernet Interface Types - Juniper Networks, Introduction to Virtual LANs (VLANs) and Tagging - Ubiquiti Support and Help Center

An LDP implicit null label causes penultimate hop popping by a downstream router. LDP is a protocol that distributes labels for MPLS forwarding along the shortest path calculated by an IGP. An implicit null label is a special label value of 3 that indicates that the downstream router does not need a label to forward the packet to its destination. When an upstream router receives an implicit null label from a downstream router, it removes (or pops) the label from the packet before sending it to the downstream router. This process is called penultimate hop popping (PHP) and it reduces the load on the downstream router, which can forward the packet based on its IP header or another label in the stack59.

References: MPLS Label Distribution Protocol Commands - Cisco, Solved: Implicit null and Explicit null - Cisco Community

Two protocols that apply to both IPv4 and IPv6 are:

SNMP: This stands for Simple Network Management Protocol, which is a protocol that allows network administrators to monitor and manage network devices such as routers, switches, servers, printers, etc. SNMP uses a client-server model, where an SNMP manager (client) can query or configure an SNMP agent (server) on a network device using SNMP messages. SNMP can operate over both IPv4 and IPv6 networks56.

DNS: This stands for Domain Name System, which is a protocol that translates human-readable domain names (such as www.example.com) into numerical IP addresses (such as 192.0.2.1 or 2001:db8::1) that identify network devices. DNS uses a hierarchical distributed database of name servers that store and resolve domain names and IP addresses. DNS can support both IPv4 and IPv6 addresses78.

References: Simple Network Management Protocol - Wikipedia, SNMP over IPv6 - Cisco, Domain Name System - Wikipedia, DNS for IPv6 - Cisco

 The operating system used in Ericsson Router 6000 products is ERS (Ericsson Router Software). ERS is based on IPOS (IP Operating System), which is a common operating system for Ericsson’s IP portfolio. ERS provides advanced features and functionality for IP transport, such as MPLS, Segment Routing, QoS, IPSec, synchronization, SDN, and more. ERS also supports seamless integration with Ericsson Radio System and Ericsson Network Manager.

References: Router 6000 Series - Ericsson, Router 6675 Datasheet - Winncom

The Area ID to which the router belongs is 49.00F0.0100. The Area ID is a variable-length field in the NSAP address that identifies the area to which the router belongs. The Area ID can be between 1 and 13 bytes long, but it must start and end with an octet (8 bits). The NSAP address is composed of three parts: the authority and format identifier (AFI), the area ID, and the system ID. The AFI is a one-octet field that indicates the format and authority of the rest of the address. The system ID is a fixed-length field of six octets that uniquely identifies the router within an area. The NSAP address also has a network selector (NSEL) field, which is a one-octet field that identifies the network layer service to which a packet should be sent. For IS-IS routers, the NSEL must always be 00.

In this question, the NSAP address is 49.00F0.0100.5012.3010.00. This means that:

The AFI is 49, which indicates a private address.

The Area ID is 00F0.0100, which is four octets long and starts and ends with an octet.

The system ID is 5012.3010, which is six octets long and identifies the router within the area.

The NSEL is 00, which indicates IS-IS.

Therefore, the answer is B.

References: Ericsson IP Networking - Routing Protocols, IS-IS NSAP address - Cisco Community, Understanding IS-IS NSAP Addresses - Todd Lammle, LLC, IS-IS - Nokia, Network service access point address - Wikipedia

P routers forward packets based on the LSP label. The LSP label is the label that corresponds to the label-switched path (LSP) that is established between two PE routers in an MPLS network. The LSP label is also called the outer label or the transport label, because it is used to transport packets across the MPLS core network. P routers are also called LSRs (label switch routers) or transit routers, because they switch packets based on their labels or remove the labels. P routers do not need to look at the IP header or any other information in the packet, except for the top label in the label stack. P routers perform one of three possible operations on labels: swap, pop, or PHP (penultimate hop popping). In a swap operation, the label is swapped with a new label, and the packet is forwarded along the path associated with the new label. In a pop operation, the label is removed from the packet, and the packet is forwarded based on its IP header or another label in the stack. In a PHP operation, the label is removed from the packet at the last P router before reaching the egress PE router, and the packet is forwarded without any label to the egress PE router.

The LSP label is different from other types of labels that may be used in MPLS networks, such as VPN labels or service labels. These labels are used to identify different VPNs or services that run over MPLS networks, such as Layer 2 VPNs, Layer 3 VPNs, traffic engineering, or QoS. These labels are also called inner labels or payload labels, because they are related to the payload of the packet. These labels are not used by P routers for forwarding decisions, but only by PE routers for delivering packets to their destinations.

Therefore, the answer is C.

References: Ericsson IP Networking - Routing Protocols, MPLS Fundamentals: Forwarding Labeled Packets - Cisco Press, MPLS Labels and Devices - NetworkLessons.com, Multiprotocol Label Switching - Wikipedia, VPN Packet Forwarding > MPLS/VPN Architecture Overview | Cisco Press, Basic concepts - Hewlett Packard Enterprise

A BGP session is established between two routers by sending a unicast OPEN message. BGP uses TCP as its transport protocol, which means that before exchanging any BGP information, a TCP connection must be established between the routers. The TCP connection uses port 179 as both source and destination port. After establishing a TCP connection, each router sends an OPEN message to its neighbor, containing parameters such as BGP version number, AS number, hold time, BGP identifier, and optional capabilities. The OPEN message also serves as a keepalive message for BGP. If both routers agree on these parameters, they proceed to exchange UPDATE messages containing routing information and establish a BGP session.

A BGP router does not send a NOTIFICATION message to establish a session, but rather to terminate a session due to an error or a manual shutdown. A BGP router does not send a CONNECT message, as this is a TCP state, not a BGP message. A BGP router does not send a multicast HELLO packet, as this is an OSPF message, not a BGP message. References: BGP Neighbor States > BGP Fundamentals | Cisco Press, Demystifying BGP Session Establishments - Packet Pushers, The TCP/IP Guide - BGP Connection Establishment: Open Messages

The correct abbreviation for the IP address BFEA:DACA:0000:0000:9390:0000:0000:D91 is BFEA:DACA::9390:0:D91. IPv6 addresses are represented in hexadecimal notation, with eight 16-bit segments separated by colons. To simplify the address representation, IPv6 supports two types of abbreviations. The first abbreviation allows us to skip leading zeros within a segment, while the second abbreviation allows us to drop one or more consecutive segments that contain only zeros, using a double colon (::) instead. However, the double colon can be used only once in an address, to avoid ambiguity34.

References: IPv6 Address Types, Notation, and Structure Explained, IPv6 address - Wikipedia

Two statements that are true about the Ericsson Router 6000 series are:

The Router 6000 uses the same building practice and accessories as the Ericsson Radio System. The Ericsson Radio System is a modular and scalableradio access network solution that supports multiple standards, bands, and layers. The Router 6000 series is fully integrated into the Ericsson Radio System, using the same building practice and accessories such as mounting kits, cables, power supplies, etc. This simplifies installation, operation, and maintenance of both radio and transport equipment78.

The Router 6000 products range from all-outdoor small site routers to large aggregation routers. The Router 6000 series consists of three main products: the Router 6672 for access, the Router 6675 for pre-aggregation, and the Router 6274 for metro aggregation. The Router 6672 is an all-outdoor small cell site router with high-capacity and low-power consumption. The Router 6675 is a combined access and E-RAN switch with hardware-accelerated IPSec and high-accuracy internal clock. The Router 6274 is a high-capacity metro aggregation router with SDN functionality and flexible interface options78.

References: Router 6000 Series - Ericsson, New Ericsson Router 6000 series couples radio and IP transport for 5G future - Global Brands Magazine

The router function that advertises external routes in OSPF is ASBR, which stands for Autonomous System Boundary Router. An ASBR is a router that connects an OSPF domain to another routing domain, such as another OSPF domain or a different routing protocol domain. An ASBR can redistribute routes from other routing domains into OSPF as external routes, which are carried in type 5 or type 7 LSAs. External routes have two types: E1 and E2. E1 routes include the cost from the ASBR to the destination, while E2 routes only include the cost advertised by the ASBR34.

References: OSPF External Routes ⋆ IpCisco, OSPF External Route selection algorithm - Cisco Community