Pass the Ericsson Certified Associate ECP-206 Questions and answers with ExamsMirror

The device that will fragment IPv6 packets is the source host. Fragmentation is a process of dividing a large packet into smaller pieces that can fit the maximum transmission unit (MTU) of the network link. In IPv4, fragmentation can be performed by either the source host or any intermediate router along the path. However, in IPv6, fragmentation is only allowed at the source host, and routers are not allowed to fragment packets. This reduces the processing overhead and complexity at routers and avoids potential fragmentation attacks. If a router receives an IPv6 packet that is too large for the next-hop link, it will drop the packet and send an ICMPv6 Packet Too Big message back to the source host56.

References: IPv6 address - Wikipedia, IPv6 Fragmentation - Cisco

Two statements that are true about router node hardening are:

Any unnecessary services should be disabled within each context. Router node hardening is a process of securing a router from unauthorized access and attacks by applying various configurations and policies. One of these configurations is to disable any services that are not needed for the router’s functionality or purpose, such as telnet, ftp, http, etc. This reduces the attack surface of the router and prevents potential exploits of these services91.

Enabling syslog ensures system events are logged to a remote server. Syslog is a protocol that allows a router to send system messages and events to a remote server for logging and analysis. By enabling syslog on a router, network administrators can monitor the router’s activity and performance, troubleshoot problems, detect anomalies, and audit security events101.

References: Cisco Router Hardening Step-by-Step | SANS Institute, Security Hardening Checklist Guide for Cisco Routers/Switches in 10 Steps, CCNA SEC: Router Hardening - Cisco Press

Two statements that are true regarding the LSP are:

The LSP refers to a sequence of routers that forward the MPLS packet based on labels. An LSP is a Label Switched Path, which is a path through an MPLS network that is established by signaling protocols such as LDP or RSVP-TE. An LSP consists of a sequence of routers (called Label Switching Routers or LSRs) that forward packets based on labels rather than IP addresses. Labels are short fixed-length identifiers that are attached to packets at the ingress router and removed at the egress router. Labels can be swapped or popped at intermediate routers according to their label forwarding tables78.

The LSP refers to a sequence of routers that add, remove, or change label values along the path. As mentioned above, an LSP consists of a sequence of routers that forward packets based on labels. Along the path, different routers may perform different operations on the labels depending on their role and configuration. The ingress router adds one or more labels to the packet before sending it into the MPLS network. The egress router removes all labels from the packet before sending it out of the MPLS network. The intermediate routers may swap one label with another label according to their label forwarding tables. This process is called label switching78.

References: MPLS Fundamentals: 3 - MPLS Packet Forwarding, Multiprotocol Label Switching - Wikipedia

IPsec provides two main features: protecting packets from modification and hiding the content of packets from observation. IPsec protects packets from modification by using cryptographic algorithms to generate and verify message authentication codes (MACs) or digital signatures for each packet. These mechanisms ensure that the packets have not been tampered with or altered in transit by unauthorized parties. IPsec hides the content of packets from observation by using encryption algorithms to scramble the payload of each packet. This prevents eavesdroppers or interceptors from reading or analyzing the data carried by the packets12.

References: What is IPsec? | How IPsec VPNs work | Cloudflare, IPsec - Wikipedia

The maximum number of unique VLAN IDs available is 4096. A VLAN ID is a 12-bit identifier that can range from 0 to 4095. However, VLAN ID 0 is reserved for tagging the priority of frames and VLAN ID 4095 is reserved for implementation use, so only VLAN IDs from 1 to 4094 are available for user configuration78. VLAN IDs are used to identify different broadcast domains or subnets on a Layer 2 network. VLAN IDs are carried in the IEEE 802.1Q tag in the Ethernet frame header.

References: What is a virtual LAN (VLAN) and how does it work with my managed switch? - NETGEAR Support, Virtual LANs (VLANs) - Cisco

Peers recognize each other’s ability to use MP-BGP extensions by advertising the ability using the capabilities field during the session establishment. MP-BGP is an extension to BGP that allows BGP to carry routing information for multiple network layer protocols, such as IPv6, VPNv4, multicast, etc. To support MP-BGP, peers need to exchange their capabilities during the session establishment phase, which consists of three steps: open, keepalive, and update. In the open message, peers can include an optional parameter called capabilities, which indicates what kind of address families and subsequent address families they can support. If both peers agree on a common set of capabilities, they can proceed to exchange routing information for those address families using update messages56.

References: Use of MP-BGP Extensions for IPv6 Interdomain Routing, MP-EBGP Configuration Example - Cisco

Priority queuing (PQ) is a queuing method that establishes four interface output queues that serve different priority levels: high, medium, normal, and low. Traffic in the highest priority queue will experience the least amount of jitter and delay compared to traffic in the other queues, because PQ always services the higher-priority queues first. However, this can also cause traffic in lower priority queues to be starved of bandwidth, especially if the highest priority queue is oversubscribed. Traffic in the highest priority queue is not only reserved for voice traffic, but can also include network control and routing traffic. Traffic in all queues are not always guaranteed a minimum bandwidth, because PQ does not provide any bandwidth reservation mechanism. References: Quality of Service (QoS) Queues and Queuing Explained, Chapter: Configuring Priority Queueing - Cisco

iBGP works by exchanging routing information between two or more routers within an AS. Each router sends its own routing table to its neighbors, which contains information about the networks it knows and how they can be reached from that router. By default, iBGP neighbors only share BGP routes learned from eBGP neighbors, which are routers in different ASes. This is because iBGP assumes that all routers within an AS have consistent internal routing information provided by an IGP, such as OSPF or IS-IS. Therefore, iBGP neighbors do not need to share IP address information of loopbackinterfaces or directly connected interfaces, unless explicitly configured to do so by using commands such as neighbor update-source or network.

References: iBGP Ultimate Guide | How iBGP Is Different From eBGP, Ericsson IP Networking - Routing Protocols