Pass the Juniper JNCIP-ENT JN0-650 Questions and answers with ExamsMirror

Junos OS 24.4 on EX Series switches provides robust support for LLDP (Link Layer Discovery Protocol) and its extension, LLDP-MED (Media Endpoint Discovery).

LLDP-MED Power Negotiation: This feature allows a switch (Power Sourcing Equipment or PSE) and a connected device (Powered Device or PD), such as an IP phone or access point, to negotiate power requirements beyond the standard IEEE 802.3af/at classes. The switch can dynamically allocate the exact amount of power the device needs (in 0.1W increments), which optimizes the power budget of the switch.

LLDP Scope: LLDP is a Link Layer protocol (Layer 2), but it is not restricted to Layer 2 interfaces; it can also operate on Layer 3 interfaces to advertise system identity and capabilities. This makes Option A incorrect.

Link-Local Protocol: LLDP frames use a specific multicast MAC address (01:80:c2:00:00:0e) that is not flooded or forwarded by switches. They are strictly link-local between two directly connected neighbors. This makes Option B incorrect.

Endpoint Focus: LLDP-MED is specifically designed for Media Endpoint Devices (like VoIP phones), providing TLVs for network policy (VLAN/QoS), location identification, and inventory management. Standard LLDP is used for discovering network connectivity devices. This makes Option D incorrect.

The exhibit shows a BGP routing process where an Import Policy is being applied to routes received in the RIB-IN. Specifically, Policy 1 states: "Reject 0.0.0.0/0 from AS 64512."

In Junos OS, when a routing policy rejects a route, that route is not placed in the main routing table (inet.0) for active use. Instead, it becomes a hidden route. To verify that a specific peer is actually sending a route that is subsequently being rejected by your policy, you must use specific diagnostic commands:

Understanding "Hidden" Routes: When a BGP route is received but fails to meet policy requirements (or has an unreachable next-hop), Junos keeps it in the BGP RIB-IN but marks it as "hidden." It will not appear in a standard show route command.

Command Logic (Option D): The command show route receive-protocol bgp hidden allows an administrator to view all routes received from a specific neighbor, including those that were rejected by import policies.

show route receive-protocol bgp : Shows only the routes that passed the import policy and were accepted into the table. Since the 0.0.0.0/0 route from AS 64512 is explicitly rejected in the exhibit, it would not show up here.

Adding the hidden keyword is the essential step to see the rejected default route and verify that AS 64512 is indeed sending it before the policy drops it.

Other Options:

Option A is incorrect because it only shows accepted routes.

Option B and C are used to filter the existing active routing table based on gateway or next-hop attributes, but they cannot show routes that have been rejected and excluded from that table.

In an EVPN-VXLAN architecture, the network is divided into two distinct planes: the Underlay and the Overlay.

Underlay (IP Fabric): The underlay's only job is to provide IP reachability between the loopback addresses of all VTEPs (Virtual Tunnel Endpoints). This is typically achieved using OSPF, IS-IS, or EBGP.

Overlay (EVPN Control Plane): The overlay is responsible for carrying Layer 2 MAC and Layer 3 IP reachability information between switches. EVPN signaling is the standard mechanism for this task.

Protocol Choice (Option D): EVPN uses MP-BGP (Multiprotocol BGP) as its control plane protocol. On Juniper EX Series and QFX Series switches, the most scalable and recommended design for the overlay is EBGP (External BGP).

In a 3-stage or 5-stage Clos architecture, EBGP is used in the overlay to exchange EVPN routes (Route Types 1-5) between Leaf and Spine switches.

EBGP simplifies configuration by avoiding the need for Route Reflectors (required for IBGP) and provides better control over route propagation through BGP community and policy management.

Incorrect Options:

Options A and B refer to the underlay protocols. While they provide the path for the VXLAN tunnels, they do not handle the EVPN signaling itself.

Option C (MPLS) is a different transport technology. While EVPN can run over MPLS (EVPN-MPLS), campus designs on EX series devices specifically use VXLAN as the data plane, making EBGP the standard signaling protocol for the EVPN-VXLAN overlay.

VSTP (VLAN Spanning Tree Protocol) is Juniper's implementation that provides a separate spanning tree instance for each VLAN, ensuring compatibility with Cisco's PVST+. However, it has significant scaling limitations:

Instance Limits: On many Juniper EX and QFX series switches, VSTP is restricted to a maximum of 253 or 510 VLAN instances depending on the software version (ELS vs. non-ELS). In your scenario, having 450 VLANs exceeds the standard 253-instance limit found on many platforms.

The Solution (Option B): When the number of VLANs exceeds the VSTP capacity, the recommended best practice is to enable RSTP (Rapid Spanning Tree Protocol). Unlike VSTP, RSTP runs a single spanning tree instance for the entire switch, regardless of how many VLANs are configured. This ensures that all 450 VLANs are protected from loops without hitting the hardware's instance-count limit.

Other Options: Option A (force-version) only affects the BPDU format for compatibility but doesn't solve the instance limit. Option C and Option D are parameter tuning actions that do not address the architectural limitation of the number of running instances.

OSPF determines the best path to a destination by calculating the metric (cost) of each link. By default, Junos OS uses a reference bandwidth of 100 Mbps to calculate this cost using the formula:

When the reference bandwidth is left at the default 100 Mbps, any interface with a speed of 100 Mbps or higher (including 1 GbE and 10 GbE) is assigned a cost of 1 because the minimum OSPF cost is 1. This results in equal-cost paths, preventing the router from preferring the faster 10 GbE link.

To ensure 10 GbE interfaces are preferred, you must create a cost differential:

Option A (Reference Bandwidth): By increasing the reference bandwidth to 10G (or higher), the calculation changes. For a 10 GbE link, the cost becomes $10,000 / 10,000 = 1$. For a 1 GbE link, the cost becomes $10,000 / 1,000 = 10$. Since OSPF prefers the path with the lowest cumulative cost, the 10 GbE link is now preferred.

Option D (Manual Metric): You can manually override the automatic cost calculation by assigning a higher metric specifically to the 1 GbE interfaces. If a 1 GbE interface is manually set to a cost of 50 and the 10 GbE interface remains at 1 (or is set to a lower value), the router will prioritize the 10 GbE path.

Option B is incorrect because a higher metric makes a path less preferred. Option C is incorrect because a 1G reference bandwidth would still result in both 1 GbE and 10 GbE interfaces having a cost of 1.

The IETF standards for EVPN-VXLAN define the scalability and forwarding behavior of the architecture.

VXLAN Scale (Statement B): The Virtual Network Identifier (VNI) is a 24-bit field in the VXLAN header. This allows for up to $2^{24}$ unique identifiers, which translates to approximately 16 million distinct VXLAN broadcast domains (segments) within a single fabric. * Forwarding Behavior (Statement D): VXLAN is a MAC-in-UDP encapsulation technology. When a Layer 2 frame enters the tunnel at a VTEP, the original Layer 2 frame (including the original source and destination MAC addresses) is encapsulated into a UDP/IP packet and transported across the IP underlay. When it reaches the egress VTEP, the header is removed and the Layer 2 frame is forwarded unchanged to the destination host.

Why others are incorrect: Statement A is incorrect because EVPN itself can technically support more than 16 million domains, but the data plane (VXLAN) is the limiting factor in this specific deployment scenario. Statement C is incorrect because VXLAN encapsulates Layer 2 frames, not just "IP packets," and it treats the entire frame as a payload.

To interoperate with Cisco switches running Per-VLAN Spanning Tree Plus (PVST+), Juniper devices must use VLAN Spanning Tree Protocol (VSTP).

PVST+ Compatibility: VSTP is specifically designed to handle the per-VLAN BPDU requirements of Cisco's PVST+. It generates a separate spanning tree instance for each VLAN and uses the same multicast destination MAC address as Cisco devices.

Other Protocols: MSTP (B) is used for grouping VLANs into regions; RSTP (D) is a single-instance protocol (IEEE 802.1w) and is generally incompatible with per-VLAN BPDU requirements without additional configuration.

In standard BGP operations, a router typically selects only one "best path" for a given destination prefix and installs that single path into the forwarding table. To utilize multiple paths for traffic forwarding (load-balancing), specific multipath features must be enabled.

BGP Multipath: This feature allows a router to install multiple equal-cost paths into the routing and forwarding tables. However, by default, BGP multipath requires that all candidate paths have the same neighboring Autonomous System (AS).

Multipath Multiple-AS (Option B): In the exhibit, R1 is receiving routes from ISP A (AS 65501) and ISP B (AS 65502). Since these are two different neighboring ASs, the standard multipath feature is not sufficient. You must use the multipath multiple-as statement under the BGP group or neighbor hierarchy. This tells Junos to consider paths as equal even if they originate from different neighboring ASs, provided all other BGP path selection attributes (Local Preference, AS Path length, Origin, MED, etc.) are identical.

Why other options are incorrect: * Option A (multihop) is used for peering with routers that are not directly connected.

Option C (prefix limit) is a security and stability feature to limit the number of prefixes received from a neighbor.

Option D (damping) is used to penalize unstable, "flapping" routes to prevent constant routing table churn.

Configuration Example for Junos OS 24.4: To implement this on R1, you would use the following configuration:

set protocols bgp group multipath multiple-as

In a three-stage EVPN-VXLAN fabric (Spine-Leaf architecture) where leaf devices perform the gateway services (Edge-Routed Bridging or ERB):

VTEP Functionality (Option B): Leaf devices act as VXLAN Tunnel End Points (VTEPs). They are responsible for encapsulating Ethernet frames from locally connected hosts into VXLAN packets for transport across the IP fabric and de-encapsulating incoming VXLAN packets.

Fabric Support (Option C): In a standard Juniper IP fabric design, both the leaf and spine devices are typically expected to support VXLAN and EVPN capabilities. While spines in an ERB design might only perform IP forwarding in the underlay, they often participate in the BGP control plane (as Route Reflectors) or provide the ability to transition to Centrally-Routed Bridging (CRB) where spines would act as gateways.

Incorrect Options: Option A is incorrect because the entire fabric infrastructure must be "VXLAN aware" in terms of MTU settings and routing capability to support the overlay. Option D is incorrect because in an ERB design, the spine devices are high-speed transit nodes and do not terminate VXLAN tunnels; only the edge (leaf) devices act as VTEPs.

The exhibit shows a custom Behavior Aggregate (BA) classifier named my-classifier for the Differentiated Services Code Point (DSCP) protocol.

Importing Defaults (Statement C): The configuration line import default; is crucial. In Junos OS, when you create a custom classifier, you can use this statement to import the default mapping table for all code points that you have not explicitly defined in the current block. This ensures that only the specific traffic types you care about are customized while the rest follows industry-standard defaults.

Logical Interface Association (Statement A): In the Junos class-of-service hierarchy, classifiers are typically applied to logical interfaces (e.g., ge-0/0/0.0). While they can sometimes be applied at a higher level, the standard practice for enterprise routing and switching is to associate them with the logical unit to provide granular control over subinterfaces or VLAN-tagged traffic.

Why others are incorrect: Statement B is less accurate because the primary binding point in Junos is the unit (logical interface). Statement D is incorrect because the specific classifications defined in the custom block override the defaults; they are not overwritten by them.