Pass the RedHat RHCE RH302 Questions and answers with ExamsMirror

Do the following steps as:

1. Create the repository file

#vi /etc/yum.repos.d/server1.repo

[station?]

name=station?

baseurl=ftp://server1.example.com/pub/

enabled=1

gpgcheck=1

gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release

# yum install

Do the following steps as:

1.useradd jeff

2.useradd marion

3.useradd harold

useradd command is used to create the user. All user’s information stores in /etc/passwd and user;s shadow password stores in /etc/shadow.

Do the following steps as:

cat >schedule

*/2 * * * * /bin/echo “Hello World” >/dev/tty8

crontab schedule

Verify using: crontab –l

service crond restart

Cron helps to schedule on recurring events. Pattern of Cron is:

MinuteHourDay of MonthMonthDay of WeekCommands

0-590-231-311-120-7 where 0 and 7 means Sunday.

Note * means every. To execute the command on every two minutes */2.

To add the scheduled file on cron job: crontab filename

To List the Cron Shedule: crontab –l

To Edit the Schedule: crontab –e

To Remove the Schedule: crontab –r

Do the following steps as:

1.dump -0u –f /tmp/back /dev/hda4

dump is the standard backup utility. According to the questions, fullback should take. –0 means fullback, -u means update the /etc/dumpdates which maintains the backup record and -f means filename. If you are directly taking backup into other device, you can specify the device name.

e dump -0u -f /dev/st0 /dev/hda4. Where hda4 is a separate partition mounted on /home.

When user creates the file/directory, user owner will be user itself and group owner will be the primary group of the user.

There is one Special Permission SGID , when you set the SGID bit on directory,When users creates the file/directory automatically owner group will be same as a parent.

chmod g+s /data

Verify using: ls -ld /data

You will get: drwxrws---

chown or chgrp command is used to change the ownership.

Syntax of chown: chown [-R] username:groupname file/directory

Syntax of chgrp: chgrp [-R] groupname file/directory

Whenever user creates the file or directory, the owner of that file/directory automatically will be that user and that user’s primary group name.

To change group owner ship

chgrp training /data Which set the Group Ownership to training

or

chown root.training /dataWhich set the user owner to root and group owner to training group.

Verify /data using: ls -ld /data

You will get: drwxr-xr-x 2 root training …………..

Do the following steps as:

useradd username

passwd username

usermod -e “date”

example: usermod -e “12 Feb 2006” user4

Verify: chage –l user4

Do the following steps as:

1.usermod -G sysusers jeff

2.usermod –G sysuser marion

3.Verify by reading /etc/group file

Using usermod command we can make user belongs to different group. There are two types of group one primary and another is secondary. Primary group can be only one butuser can belongs to more than one group as secondary.

usermod -g groupname usernameTo change the primary group of the user

usermod -G groupname usernameTo make user belongs to secondary group.

Do the following steps as:

1.vi /etc/squid/squid.conf

#detault:

http_port8080

#Recommended minimum configuration:

# Near the src acl src section

acl allownet src 192.168.0.0/255.255.255.0

acl msnnet dstdomain .msn.com

#Default:

# http_access deny all

#Under Herehttp_access deny msnnet

http_access allow allownet

2.service squid start

3.chkconfig squid on

squid is a proxy caching server, using squid we can share the internet, block the internet, to certain network. First we should define the port for squid, the standard port for squid is 3128. We can run squid on different port by specifying http_port portnumber.

To block or allow the Internet access to hosts, we should create the acl (Access Control List). In this file we can specify only the IP address.

Example: acl aclname src IP/NetmaskAfter creating acl we can block or allow the Internet to specified acl.

http_access allow | deny alcname

Do the following steps as:

1.vi /etc/xinetd.d/telnet

service telnet {

only_from=192.168.0.0/24

access_times=09:00-17:00

}

2.chkconf telnet on

3.service xinetd restart

xinetd based services can manage by specifying host and time parameters. Only_from means connection allowed network, remaining hosts explicitly deny. access_times specify when service is available.