Pass the Checkpoint CCSA R81 156-215.81 Questions and answers with ExamsMirror

Multi-domain management server is a valid deployment option for R81, not R80. R80 supports multi-domain security management, which is a centralized management solution for large-scale, distributed environments with many different domain networks1. References: Multi-Domain Security Management Administration Guide R80

This answer is correct because DES (Data Encryption Standard) is the least secured encryption algorithm among the options given. DES uses a 56-bit key, which is too short and can be easily cracked by brute force attacks1. DES also suffers from other weaknesses, such as weak keys, complementation property, and linear cryptanalysis2.

The other answers are not correct because they are more secured encryption algorithms than DES. 3DES (Triple DES) is an improvement over DES that applies DES three times with different keys, resulting in a 168-bit key3. AES-128 and AES-256 are variants of AES (Advanced Encryption Standard) that use 128-bit and 256-bit keys respectively. AES is considered to be the most secure symmetric encryption algorithm and is widely used for data protection.

What is DES encryption, and why was it replaced?

Data Encryption Standard - Wikipedia

What is 3DES encryption?

[What is AES encryption and how does it work?]

A security zone is a group of one or more network interfaces from different centrally managed gateways that have the same security requirements. The zone is based on the network topology and determined according to where the interface leads to. For example, a zone can be defined as internal, external, DMZ, VPN, etc. Security zones are supported by Check Point firewalls and can be used to simplify security policies and network segmentation. The firewall rule can be configured to include one or more zones as source or destination objects. The local directly connected subnet defined by the subnet IP and subnet mask is not considered part of the zone, but rather a property of the interface.References: [Security Zones], [Security Zones Best Practices]

The tool that is used to enable ClusterXL is cpconfig. ClusterXL is a software-based Load Sharing and High Availability solution that distributes network traffic between clusters of redundant Security Gateways1. To enable ClusterXL, you need to run the cpconfig command on each cluster member and select Enable Cluster membership for this gateway2. Therefore, the correct answer is B. cpconfig. 

NAT (Network Address Translation) is a technique that modifies the IP addresses or ports of packets that pass through a security gateway. NAT can be configured in two ways: Automatic or Manual. Automatic NAT means that the NAT rules are generated automatically by the security gateway based on the NAT properties of network objects. Manual NAT means that the NAT rules are defined explicitly by the administrator in the NAT policy. Proxy ARP (Address Resolution Protocol) is a technique that allows a security gateway to answer ARP requests on behalf of other hosts. Proxy ARP is needed when a host on one network segment tries to communicate with a host on another network segment that has a different IP address than its own. In some scenarios, an administrator will need to manually define Proxy ARP for NAT to work properly. One such scenario is when they configure a Manual Static NAT which translates to an IP address that does not belong to one of the firewall’s interfaces2. References: Check Point R81 Network Address Translation Administration Guide

 Core Protections are installed as part of the Threat Prevention Policy. Core Protections are a set of IPS protections that are essential for securing your network against malicious traffic4. The other policies do not include Core Protections.

References: 1: Check Point CLI Reference Card 2: Anti-Spoofing 3: SmartView Tracker 4: Core Protections

When LDAP is integrated with Check Point Security Management, it is then referred to as User Directory. User Directory is a feature that allows administrators to manage users and user groups from an external LDAP server, such as Active Directory2.

References: 2: Check Point R81 Identity Awareness Administration Guide, page 9.

The steps you will need to do in SmartConsole in order to get the connection working behind the Internet Security Gateway are:

Define an accept rule in Security Policy. This rule allows the traffic from your internal networks to pass through the Security Gateway.

Define automatic NAT for each network to NAT the networks behind a public IP. This option translates the private IP addresses of your internal networks to a public IP address assigned by your ISP router. This way, your internal networks can communicate with the Internet using a valid IP address.

Publish and install the policy. This step applies the changes you made to the Security Gateway and activates the security and NAT rules.

References: Check Point R81 Quantum Security Gateway Guide

Detailed Log is not a valid tracking log option in R80.x3. The tracking log options in R80.x are Log, Full Log, and Extended Log45. References: Where is ‘full log’ option in track column, LOGGINGAND MONITORING R80, Logging and Monitoring Administration Guide R80.20

According to the Learn More About Threat Signatures4, to quickly review when Threat Prevention signatures were last updated, you can use the IPS Protections tool. This tool shows you the date and time of the last update, as well as the number of signatures and their categories. References: Learn More About Threat Signatures