Summer Certification Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = getmirror

Home
Cisco
CCNP Service Provider
300-510
Implementing Cisco Service Provider Advanced Routing Solutions Questions and Answers

Pass the Cisco CCNP Service Provider 300-510 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.

Exam 300-510 Premium Access

View all detail and faqs for the 300-510 exam

Go to Exam

792 Students Passed

94% Average Score

93% Same Questions

Viewing page 3 out of 8 pages

Viewing questions 21-30 out of questions

Questions # 21:

Refer to the exhibit.

Question # 21

An engineer is comparing these RPL and route map configurations. Which two conclusions will the engineer reach? (Choose two.)

Options:

RPL is applying policy only on BGP IPv6 address families, but the route map is applying policy on BGP IPv4 and IPv6 address families.

RPL and the route map are applying only local preference 50 for prefix 172.22.0.0/16.

RPL is applying local preference 100 and community (2:100) for multiple prefixes, but the route map is applying default local preference for multiple prefixes

RPL is applying local preference 50 and community (2:666) for prefix 172.22.0.0716. but the route map is applying only local preference 50 for the same prefix

RPL is applying local preference 50 and community (2:666) for all prefixes, but the route map is applying only local preference 50 for all prefixes.

Answer

C, D

Questions # 22:

An ISP has an MPLS VPN-based network with 12 PE routers. How many peerings are required between the 12 routers if the engineer has not configured route reflectors?

Options:

Answer

Questions # 23:

Drag and drop the BGP attributes from the left into the order of route selection preference on the right.

Question # 23

Options:

Answer

Answer:

Questions # 24:

Question # 24

Refer to the exhibit. HostB receives an IPTV traffic stream from the multicast source at 192.168 10.1. When router RB is powered down, it impacts multicast traffic forwarding to downstream peers. The RA and RB routers reside in the same physical location. Which two configurations must be implemented so that HostB receives the multicast stream even when RB is powered down? (Choose two )

Options:

Enable PIM sparse mode on routers RC and RZ with a static RP address of 10.10.10.1.

Set the backup RP address to 10 10 10.3 on routers RY and RZ.

Enable bi-directional PIM on all routers.

Enable PIM SSM mode on routers RA and RY.

Set the RP address to 10.10.10.4 on all routers

Answer

A, D

Questions # 25:

What is the difference between RPL and route-maps?

Options:

Unlike RPL. route-maps are supported with IPv4 address families only

Unlike route-maps, only RPL supports extcommunity sets to group extended communities.

Unlike RPL. route-maps are designed for BGP protocol only.

Unlike route-maps, only RPL is designed for bulk configuration of multiple devices.

Answer

Questions # 26:

Which attribute is used to instruct the router that packets must be processed by an ASA that is associated with the segment?

Options:

service SID with service instructions

node SID that identifies a specific network device

prefix SID that represents a specific route prefix

adjacency SID with unidirectional adjacency instructions

Answer

Questions # 27:

Refer to the exhibit.

Question # 27

An engineer is troubleshooting connectivity issues on the MPLS core network. A customer connected through R4 cannot reach the OSPF domain on R5. While checking the routing table of R1, the engineer cannot see all the routes from R3 and R5. Which task must the engineer perform so that R4 is able to reach R5?