Summer Certification Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = getmirror

Pass the Cisco CCNP Enterprise 300-410 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.

Exam 300-410 Premium Access

View all detail and faqs for the 300-410 exam

Go to Exam

731 Students Passed

84% Average Score

98% Same Questions

Viewing page 2 out of 13 pages

Viewing questions 16-30 out of questions

Questions # 16:

Which configuration feature should be used to block rogue router advertisements instead of using the IPv6 Router Advertisement Guard feature?

Options:

VACL blocking broadcast frames from nonauthorized hosts

PVLANs with promiscuous ports associated to route advertisements and isolated ports for nodes

PVLANs with community ports associated to route advertisements and isolated ports for nodes

IPv4 ACL blocking route advertisements from nonauthorized hosts

Questions # 17:

Question # 17

Refer to the exhibit. A network administrator configured NTP on a Cisco router to get synchronized time for system and logs from a unified time source The configuration did not work as desired Which service must be enabled to resolve the issue?

Options:

Enter the service timestamps log datetime localtime global command.

Enter the service timestamps log datetime synchronize global command.

Enter the service timestamps log datetime console global command.

Enter the service timestamps log datetime clock-period global command

Questions # 18:

Question # 18

Refer to the exhibit. The network administrator has configured the Customer Edge router (AS 64511) to send only summarized routes toward ISP-1 (AS 100) and ISP-2 (AS 200).

router bgp 64511

network 172.16.20.0 mask 255.255.255.0

network 172.16.21.0 mask 255.255.255.0

network 172.16.22.0 mask 255.255.255.0

network 172.16.23.0 mask 255.255.255.0

aggregate-address 172.16.20.0 255.255.252.0

After this configuration. ISP-1 and ISP-2 continue to receive the specific routes and the summary route. Which configuration resolves the issue?

Options:

router bgp 64511aggregate-address 172.16.20.0 255.255.252.0 summary-only

router bgp 64511neighbor 192.168.100.1 summary-onlyneighbor 192.168.200.2 summary-only

interface E 0/0ip bgp suppress-map BLOCK_SPECIFIC!interface E 0/1ip bgp suppress-map BLOCK_SPECIFIC!ip prefix-list PL_BLOCK_SPECIFIC permit 172.16.20.0/22 ge 24!route-map BLOCK_SPECIFIC permit 10match ip address prefix-list PL_BLOCK_SPECIFIC

ip prefix-list PL_BLOCK_SPECIFIC deny 172.16.20.0/22 ge 22ip prefix-list PL BLOCK SPECIFIC permit 172.16.20.0/22!route-map BLOCK_SPECIFIC permit 10match ip address prefix-list PL_BLOCK_SPECIFIC!router bgp 64511aggregate-address 172.16.20.0 255 255.252.0 suppress-map BLOCKSPECIFIC

Questions # 19:

Refer to the exhibit.

Question # 19

A network administrator reviews the branch router console log to troubleshoot the OSPF adjacency issue with the DR router. Which action resolves this issue?

Options:

Advertise the branch WAN interface matching subnet for the DR site.

Configure matching hello and dead intervals between sites.

Configure the WAN interface for DR site in the related OSPF area.

Stabilize the DR site flapping link to establish OSPF adjacency.

Questions # 20:

Refer to the exhibit.

Question # 20

Which action resolves the adjacency issue?

Options:

Match the hello interval timers.

Configure the same EIGRP process IDs.

Match the authentication keys.

Configure the same autonomous system numbers.

Questions # 21:

Question # 21

Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?

Options:

Enable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command

Disable IPv6 on the E 0/0 interface using the no ipv6 enable command

Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command

Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface.

Questions # 22:

Refer to the exhibit.

Question # 22

An engineer wanted to set a tag of 30 to route 10 1.80.65/32 but it failed How is the issue fixed?

Options:

Modify route-map ospf-to-eigrp permit 30 and match prefix-list ccnp2.

Modify route-map ospf-to-eigrp permit 10 and match prefix-list ccnp2.

Modify prefix-list ccnp3 to add 10.1.64.0/20 le 24

Modify prefix-list ccnp3 to add 10.1.64.0/20 ge 32

Questions # 23:

Refer to the exhibit.

Question # 23

The R1 and R2 configurations are:

Question # 23

The neighbor is not coming up. Which two sets of configurations bring the neighbors up? (Choose two.)

Options:

R2ip route 10.1.1.1 255.255.255.255 192.168.1.1！router bgp 200neighbor 10.1.1.1 tti-security hops 1neighbor 10.1.1.1 update-source loopback 0

R2ip route 10.1.1.1 255.255.255.255 192.168.1.1！router bgp 200neighbor 10.1.1.1 disable-connected-checkneighbor 10.1.1.1 update-source loopback 0

R2ip route 10.1.1.2 255.255.255.255 192.168.1.2！router bgp 100neighbor 10.1.1.2 ttl-security hops 1neighbor 10.1.1.2 update-source loopback 0

R1ip route 10.1.1.2 255.255.255.255 192.168.1.2！router bgp 100neighbor 10.1.1.1 ttl-security hops 1neighbor 10.1.1.2 update-source loopback 0

R1ip route 10.1.1.2 255.255.255.255 192.168.1.2！router bgp 100neighbor 10.1.1.2 disable-connected-checkneighbor 10.1.1.2 update-source Loopback0

Questions # 24:

Question # 24

Refer to the exhibit. R1 and R2 cannot establish an EIGRP adjacency. Which action establishes EIGRP adjacency?

Options:

Remove the current autonomous system number on one of the routers and change to a different value.

Remove the passive-interface command from the R2 configuration so that it matches the R1 configuration.

Add the no auto-summary command to the R2 configuration so that it matches the R1 configuration.

Add the passive-interface command to the R1 configuration so that it matches the R2 configuration.

Questions # 25:

Refer to Exhibit.

A network administrator has successfully configured DMVPN topology between a hub and two spoke routers. Which two configuration commands should establish direct communications between spoke 1 and spoke 2 without going through the hub? (Choose two).

Question # 25

Options:

At the hub router, configure the ip nhrp shortcut command.

At the spoke routers, configure the ip nhrp spoke-tunnel command.

At the hub router, configure ip nhrp redirect the command

At the spoke routers, configure the ip nhrp shortcut command.

At the hub router, configure tne Ip nhrp spoke-tunnel command

Questions # 26:

Refer to the exhibit.

Question # 26

The network administrator configured redistribution on an ASBR to reach to all WAN networks but failed Which action resolves the issue?

Options:

The route map must have the keyword prefix-list to evaluate the prefix list entries

The OSPF process must have a metric when redistributing prefixes from EIGRP.

The route map EIGRP->OSPF must have the 10.0.106.0/24 entry to exist in one of the three prefix lists to pass

EIGRP must redistribute the 10.0.106.0/24 route instead of using the network statement

Questions # 27:

Refer to the exhibit.

Question # 27

Troubleshoot and ensure that branch B only ever uses the MPLS B network to reach HQ. Which action achieves this requirement?

Options:

Introduce an AS path filter on branch A routers so that only local prefixes are advertised into BGP

increase the local preference for all HQ prefixes received at branch B from the MPLS B network to be higher than the local preferences used on the MPLS A network

Introduce AS path prepending on the branch A MPLS B network connection so that any HQ advertisements from branch A toward the MPLS B network are prepended three times

Modify the weight of all HQ prefixes received at branch B from the MPLS B network to be higher than the weights used on the MPLS A network

Questions # 28:

Which two components are needed for a service provider to utilize the LVPN MPLS application? (Choose two.)

Options:

The P routers must be configured for MP-iBGP toward the PE routers

The P routers must be configured with RSVP.

The PE routers must be configured for MP-iBGP with other PE routers

The PE routers must be configured for MP-eBGP to connect to CEs

The P and PE routers must be configured with LDP or RSVP

Questions # 29:

Refer to the exhibit.

Question # 29

A network is under a cyberattack. A network engineer connected to R1 by SSH and enabled the terminal monitor via SSH session to find the source and destination of the attack. The session was flooded with messages, which made it impossible for the engineer to troubleshoot the issue. Which command resolves this issue on R1?

Options:

no terminal monitor

(config)#terminal no monitor

#terminal no monitor

(config)#no terminal monitor

Questions # 30:

Refer to Exhibit.

Question # 30

A network administrator added one router in the Cisco DNA Center and checked its discovery and health from the Network Health Dashboard. The network administrator observed that the router is still showing up as unmonitored. What must be configured on the router to mount it in the Cisco DNA Center?