Summer Certification Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = getmirror

Pass the Riverbed RCPE-CP-WO 830-01 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.
Exam 830-01 Premium Access

View all detail and faqs for the 830-01 exam

Go to Exam

776 Students Passed

97% Average Score

97% Same Questions
Viewing page 2 out of 12 pages
Viewing questions 11-20 out of questions
Questions # 11:

You see errors such as the following in the SteelHead messages log “error=SMB_SHUTDOWN_ERR_SEC_SIG_ENABLED”. What do these indicate?

Options:

A.

SMB signing has been detected on SMB sessions which the SteelHead attempted to optimize, but SMB signing is not configured on the SteelHeads.

B.

The SteelHeads are configured to carry secure traffic over SSI and the inner channel failed to establish.

C.

The optimization service encountered an error, and the SMB blade has been shut down.

D.

The SteelHead encountered a kernel error and was forced to shut down.

E.

The server send a secure signal to terminate an optimized SMB session.

Questions # 12:

On the Interceptor appliance, connection tracing feature enables you:

Options:

A.

To determine to which Interceptor appliances the Virtual Steelhead appliance has redirected specific connections.

B.

To determine to which Interceptor appliances the Steelhead appliance has redirected specific connections.

C.

To determine to which Steelhead appliances the Interceptor appliance has redirected specific connections.

D.

To determine to which Mobile Controller the Interceptor appliance has redirected specific connections.

Questions # 13:

What type of problem does the error message below indicate:

Sep 13 03:50:51 SH alarmd[18371]: [alarmd.NOTICE]: Alarm 'admission_mem' triggering

Sep 13 03:50:51 SH alarmd[18371]: [alarmd.NOTICE]: Alarm 'admission_control' triggering

Sep 13 03:50:51 SH alarmd[18371]: [alarmd.NOTICE]: Alarm 'health' severity changed to 'Admission Control'

Options:

A.

High CPU Utilization

B.

Paging alarm

C.

Admission control on connections

D.

Admission control on memory

E.

Admission control on system

Questions # 14:

-- Exhibit –

Question # 14

-- Exhibit --

Refer to the exhibit. According to the packet capture, what statements are true? (Select 2)

Options:

A.

This Steelhead appliance is configured with enhanced auto-discovery.

B.

This Steelhead appliance is configured with enhanced peering discovery.

C.

The SYN packet coming from 172.16.12.99 with a destination to 172.16.11.88 carries a probe of 10 bytes.

D.

The SYN packet coming from 172.16.12.99 with a destination to 172.16.11.88 carries a probe of 10 bytes + a 4 bytes notification message.

Questions # 15:

-- Exhibit –

Question # 15

-- Exhibit --

Refer to the exhibit. In a WCCP environment with R3, SH10 and SH11, which statement below is true?

Options:

A.

The Steelhead appliance is only receiving HTTP traffic from the router.

B.

All traffic will be sent from the router to the Steelhead appliance.

C.

The Steelhead appliance will not receive HTTP traffic from the router.

D.

There is no need to use access-lists on the router to select HTTP traffic.

E.

The Steelhead appliance is only receiving traffic on port TCP 1741.

Questions # 16:

You have a number of SteelHeads running RiOS 9.x. At each datacenter site, there are a cluster of domain controllers, one of which the SteelHead is connected to. As the volume of users on the network increase, the load which the server-side SteelHeads are placing on the connected domain controller pushes the domain to its limits, and authentication failures sometimes occur. What is the best way to address this?

Options:

A.

Increase the time Kerberos tickets are cached for individual users on the SteelHeads.

B.

Identify traffic which does not have a high rate of data reduction, and use in-path rules to path this traffic through.

C.

Disable Kerberos authentication on the SteelHeads so as to down negotiate to NTLM, specifying multiple domain controllers during the domain-join.

D.

Configure domain controller load-balancing so the SteelHead can communicate with multiple domain controllers instead of just one.

Questions # 17:

When optimizing applications that open many short-lived HTTP connections, which operating mode will give the best performance?

Options:

A.

Full Transparency

B.

Full Transparency with reset

C.

Correct Addressing

D.

Port Transparency

E.

Any of the above, because performance is not affected by these

Questions # 18:

Which hypervisor platforms are officially supported by Virtual SteelHead? (Choose three.)

Options:

A.

Virtual Box

B.

Hyper-V

C.

KVM

D.

VMware Fusion

E.

ESXi

Questions # 19:

-- Exhibit –

Question # 19

-- Exhibit --

Refer to the exhibit. When USER1 tried to map shares to Server 1 and Server 2, he got the results shown. What does the report represent? (Select 2)

Options:

A.

The connection to Server 2 is optimized. The performance should be good.

B.

The connection to Server 2 is optimized, with errors, the performance should be poor.

C.

The connection to Server 1 is optimized. The performance should be good.

D.

The connection to Server 1 is optimized, with errors, the performance should be poor.

E.

The connection to Server 1 is not being optimized.

Questions # 20:

A SteelHead is running RiOS v8.6 and has an inpath0_0 IP address of 192.168.1.10. It is later upgraded from v8.6 to v9.0. As part of an IT project, the inpath0_0 IP address is changed to 10.10.10.10 and the configuration saved. Some time passes and the administrator decides to revert to RiOS v 8.6. It hasn’t been factory reset. The appliance boots and the Management Console User Interface is reachable, however, optimization no longer works. What has happened?

Options:

A.

The web GUI SSL certificate is no longer trusted and the services require a restart.

B.

The licenses are no longer valid and will need to be replaced and the services restarted.

C.

It is not possible to revert to older versions of RiOS and the optimization service has stopped as a precaution.

D.

The configuration has reverted to the one running under v8.6 and the inpath0_0 IP address is back to 192.168.1.10.

E.

The configuration has been lost and the appliance is running factory default settings.

Viewing page 2 out of 12 pages
Viewing questions 11-20 out of questions
TOP CODES

TOP CODES

Top selling exam codes in the certification world, popular, in demand and updated to help you pass on the first try.

2V0-11.25
ADM-201
Agentforce-Specialist
CMMC-CCP
Data-Cloud-Consultant
PDI
PSE-Strata-Pro-24
Secure-Software-Design
Sharing-and-Visibility-Architect
Workday-Pro-Integrations
ZDTA