Summer Certification Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = getmirror

Pass the Cisco CCNA 200-301 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.

Exam 200-301 Premium Access

View all detail and faqs for the 200-301 exam

Go to Exam

797 Students Passed

92% Average Score

91% Same Questions

Viewing page 8 out of 8 pages

Viewing questions 351-400 out of questions

Questions # 351:

Which result occurs when PortFast is enabled on an interface that is connected to another switch?

Options:

Spanning tree may fail to detect a switching loop in the network that causes broadcast storms

VTP is allowed to propagate VLAN configuration information from switch to switch automatically.

Root port choice and spanning tree recalculation are accelerated when a switch link goes down

After spanning tree converges PortFast shuts down any port that receives BPDUs.

Questions # 352:

A network administrator needs to aggregate 4 ports into a single logical link which must negotiate layer 2 connectivity to ports on another switch. What must be configured when using active mode on both sides of the connection?

Options:

802.1q trunks

Cisco vPC

LLDP

LACP

Questions # 353:

Refer to the exhibit.

Question # 353

Between which zones do wireless users expect to experience intermittent connectivity?

Options:

between zones 1 and 2

between zones 2 and 5

between zones 3 and 4

between zones 3 and 6

Questions # 354:

Refer to the exhibit.

Question # 354

An engineer configured the New York router with state routes that point to the Atlanta and Washington sites. When command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?

Options:

ipv6 route ::/0 Serial 0/0/1

ipv6 route 0/0 Serial 0/0/0

ipv6 route ::/0 Serial 0/0/0

ip route 0.0.0.0.0.0.0.0 Serial 0/0/0

ipv6 route ::/0 2000::2

Questions # 355:

Refer to the exhibit.

Question # 355

Based on the LACP neighbor status, in which mode is the SW1 port channel configured?

Options:

passive

mode on

auto

active

Questions # 356:

A user configured OSPF and advertised the Gigabit Ethernet interface in OSPF By default, which type of OSPF network does this interface belong to?

Options:

point-to-multipoint

point-to-point

broadcast

nonbroadcast

Questions # 357:

Drag and drop the descriptions from the left onto the configuration-management technologies on the right.

Question # 357

Options:

Questions # 358:

An administrator must secure the WLC from receiving spoofed association requests. Which steps must be taken to configure the WLC to restrict the requests and force the user to wait 10 ms to retry an association request?

Options:

Enable Security Association Teardown Protection and set the SA Query timeout to 10

Enable MAC filtering and set the SA Query timeout to 10

Enable 802.1x Layer 2 security and set me Comeback timer to 10

Enable the Protected Management Frame service and set the Comeback timer to 10

Questions # 359:

Which action does the router take as rt forwards a packet through the network?

Options:

The router replaces the source and desinaoon labels wth the sending router uterface label as a source and the next hop router label as a desbnabon

The router encapsulates the source and destination IP addresses with the sending router P address as the source and the neighbor IP address as the destination

The router replaces the original source and destination MAC addresses with the sending router MAC address as the source and neighbor MAC address as the destination

The router encapsulates the original packet and then includes a tag that identifies the source router MAC address and transmit transparently to the destination

Questions # 360:

How does CAPWAP communicate between an access point in local mode and a WLC?

Options:

The access point must directly connect to the WLC using a copper cable

The access point must not be connected to the wired network, as it would create a loop

The access point must be connected to the same switch as the WLC

The access point has the ability to link to any switch in the network, assuming connectivity to the WLC

Questions # 361:

What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?

Options:

No router ID is set, and the OSPF protocol does not run.

The highest up/up physical interface IP address is selected as the router ID.

The lowest IP address is incremented by 1 and selected as the router ID.

The router ID 0.0.0.0 is selected and placed in the OSPF process.

Questions # 362:

What makes Cisco DNA Center different from traditional network management applications and their management of networks?

Options:

It omits supports auto-discovery of network elements in a greenfield deployment.

It modular design allows someone to implement different versions to meet the specific needs of an organization

It abstracts policy from the actual device configuration

It does not support high availability of management functions when operating in cluster mode

Questions # 363:

Refer to the exhibit.

Question # 363

Between which zones do wireless users expect to experience intermittent connectivity?

Options:

between zones 1 and 2

between zones 2 and 5

between zones 3 and 4

between zones 3 and 6

Questions # 364:

Refer to the exhibit.

Question # 364

Which prefix does Router 1 use for traffic to Host A?

Options:

10.10.10.0/28

10.10.13.0/25

10.10.13.144/28

10.10.13.208/29

Questions # 365:

An engineer must configure a WLAN using the strongest encryption type for WPA2- PSK. Which cipher fulfills the configuration requirement?

Options:

WEP

RC4

AES

TKIP

Questions # 366:

What are two characteristics of a controller-based network? (Choose two)

Options:

The administrator can make configuration updates from the CLI

It uses northbound and southbound APIs to communicate between architectural layers

It moves the control plane to a central point.

It decentralizes the control plane, which allows each device to make its own forwarding decisions

It uses Telnet to report system issues.

Questions # 367:

An engineer requires a scratch interface to actively attempt to establish a trunk link with a neighbor switch. What command must be configured?

Options:

switchport mode trunk

switchport mode dynamic desirable

switchport mode dynamic auto

switchport nonegotiate

Questions # 368:

Refer to the exhibit.

Question # 368

Which action is expected from SW1 when the untagged frame is received on the GigabitEthernet0/1 interface?

Options:

The frame is processed in VLAN 5.

The frame is processed in VLAN 11

The frame is processed in VLAN 1

The frame is dropped

Questions # 369:

How do AAA operations compare regarding user identification, user services and access control?

Options:

Authorization provides access control and authentication tracks user services

Authentication identifies users and accounting tracks user services

Accounting tracks user services, and authentication provides access control

Authorization identifies users and authentication provides access control

Questions # 370:

Refer to the exhibit.

Question # 370

If R1 receives a packet destined to 172.161.1, to which IP address does it send the packet?

Options:

192.168.12.2

192.168.13.3

192.168.14.4

192.168.15.5

Questions # 371:

Which function is performed by DHCP snooping?

Options:

propagates VLAN information between switches

listens to multicast traffic for packet forwarding

provides DDoS mitigation

rate-limits certain traffic

Questions # 372:

Refer to the exhibit.

Question # 372

Router R2 is configured with multiple routes to reach network 10 1.1 0/24 from router R1. What protocol is chosen by router R2 to reach the destination network 10.1 1 0/24?

Options:

eBGP

static

OSPF

EIGRP

Questions # 373:

A network administrator enabled port security on a switch interface connected to a printer. What is the next configuration action in order to allow the port to learn the MAC address of the printer and insert it into the table automatically?

Options:

enable dynamic MAC address learning

implement static MAC addressing.

enable sticky MAC addressing

implement auto MAC address learning

Questions # 374:

What does an SDN controller use as a communication protocol to relay forwarding changes to a southbound API?

Options:

OpenFlow

Java

REST

XML

Questions # 375:

Router A learns the same route from two different neighbors, one of the neighbor routers is an OSPF neighbor and the other is an EIGRP neighbor. What is the administrative distance of the route that will be installed in the routing table?

Options:

110

115

Questions # 376:

Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface?

Options:

configure a stateful DHCPv6 server on the network

enable SLAAC on an interface

disable the EUI-64 bit process

explicitly assign a link-local address

Questions # 377:

What is the expected outcome when an EUI-64 address is generated?

Options:

The seventh bit of the original MAC address of the interface is inverted

The interface ID is configured as a random 64-bit value

The characters FE80 are inserted at the beginning of the MAC address of the interface

The MAC address of the interface is used as the interface ID without modification

Questions # 378:

An organization secures its network with multi-factor authentication using an authenticator app on employee smartphone. How is the application secured in the case of a user’s smartphone being lost or stolen?

Options:

The application requires an administrator password to reactivate after a configured Interval.

The application requires the user to enter a PIN before it provides the second factor.

The application challenges a user by requiring an administrator password to reactivate when the smartphone is rebooted.

The application verifies that the user is in a specific location before it provides the second factor.

Questions # 379:

Refer to the exhibit.

Question # 379

A network engineer is in the process of establishing IP connectivity between two sites. Routers R1 and R2 are partially configured with IP addressing. Both routers have the ability to access devices on their respective LANs. Which command set configures the IP connectivity between devices located on both LANs in each site?

Question # 379

Options:

Option A

Option B

Option C

Option D

Questions # 380:

Refer to the exhibit.

Question # 380

The nip server 192.168.0.3 command has been configured on router 1 to make it an NTP client of router 2. Which command must be configured on router 2 so that it operates in server-only mode and relies only on its internal clock?

Options:

Router2(config)#ntp passive

Router2(config)#ntp server 172.17.0.1

Router2(config)#ntp master 4

Router2(config)#ntp server 192.168.0.2

Questions # 381:

What is the primary different between AAA authentication and authorization?

Options:

Authentication verifies a username and password, and authorization handles the communication between the authentication agent and the user database.

Authentication identifies a user who is attempting to access a system, and authorization validates the users password

Authentication identifies and verifies a user who is attempting to access a system, and authorization controls the tasks the user can perform.

Authentication controls the system processes a user can access and authorization logs the activities the user initiates

Questions # 382:

Refer to the exhibit.

Question # 382

A network administrator has been tasked with securing VTY access to a router. Which access-list entry accomplishes this task?

Options:

access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq ssh

access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eq scp

access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eq telnet

access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq https

Questions # 383:

Which condition must be met before an NMS handles an SNMP trap from an agent?

Options:

The NMS software must be loaded with the MIB associated with the trap.

The NMS must be configured on the same router as the SNMP agent

The NMS must receive a trap and an inform message from the SNMP agent within a configured interval

The NMS must receive the same trap from two different SNMP agents to verify that it is reliable.

Questions # 384:

Which function does an SNMP agent perform?

Options:

it sends information about MIB variables in response to requests from the NMS

it requests information from remote network nodes about catastrophic system events.

it manages routing between Layer 3 devices in a network

it coordinates user authentication between a network device and a TACACS+ or RADIUS server

Questions # 385:

Refer to the exhibit.

Question # 385

How does router R1 handle traffic to 192.168.10.16?

Options:

It selects the IS-IS route because it has the shortest prefix inclusive of the destination address.

It selects the EIGRP route because it has the lowest administrative distance.

It selects the OSPF route because it has the lowest cost.

It selects the RIP route because it has the longest prefix inclusive of the destination address.

Questions # 386:

What is the function of a server?

Options:

It transmits packets between hosts in the same broadcast domain.

It provides shared applications to end users.

It routes traffic between Layer 3 devices.

It Creates security zones between trusted and untrusted networks

Questions # 387:

Which command must be entered to configure a DHCP relay?

Options:

ip helper-address

ip address dhcp

ip dhcp pool

ip dhcp relay

Questions # 388:

What is the purpose of an SSID?

Options:

It provides network security

It differentiates traffic entering access posits

It identities an individual access point on a WLAN

It identifies a WLAN

Questions # 389:

Drag and drop the AAA terms from the left onto the description on the right.

Question # 389

Options:

Questions # 390:

Drag and drop the TCP/IP protocols from the left onto the transmission protocols on the right

Question # 390

Options:

Questions # 391:

Which protocol requires authentication to transfer a backup configuration file from a router to a remote server?

Options:

DTP

FTP

SMTP

TFTP

Questions # 392:

Refer to Exhibit.

Question # 392

How does SW2 interact with other switches in this VTP domain?

Options:

It processes VTP updates from any VTP clients on the network on its access ports.

It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports

It forwards only the VTP advertisements that it receives on its trunk ports.

It transmits and processes VTP updates from any VTP Clients on the network on its trunk ports

Questions # 393:

What role does a hypervisor provide for each virtual machine in server virtualization?

Options:

infrastructure-as-a-service.

Software-as-a-service

control and distribution of physical resources

services as a hardware controller.

Questions # 394:

What Is the path for traffic sent from one user workstation to another workstation on a separate switch In a Ihree-lter architecture model?

Options:

access - core - distribution - access

access - distribution - distribution - access

access - core - access

access -distribution - core - distribution - access

Questions # 395:

Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.

Question # 395

Options:

Questions # 396:

Using direct sequence spread spectrum, which three 2.4-GHz channels are used to limit collisions?

Options:

1,6,11

1,5,10

1,2,3

5,6,7

Questions # 397:

Which 802.11 frame type is indicated by a probe response after a client sends a probe request?

Options:

action

management

control

data

Questions # 398:

Which technology must be implemented to configure network device monitoring with the highest security?

Options:

IP SLA

syslog

NetFlow

SNMPv3

Questions # 399:

Refer to the exhibit.

Question # 399

Which route type does the routing protocol Code D represent in the output?

Options:

internal BGP route

/24 route of a locally configured IP

statically assigned route

route learned through EIGRP

Questions # 400:

Refer to the exhibit.

Question # 400

Shortly after SiteA was connected to SiteB over a new single-mode fiber path users at SiteA report intermittent connectivity issues with applications hosted at SiteB What is the cause of the intermittent connectivity issue?