Pass the CompTIA A+ 220-1201 Questions and answers with ExamsMirror

A smart card provides an additional factor of authentication by storing secure credentials, such as certificates, that cannot be guessed or replicated. It complements user accounts and is "something you have".

Why Not A (Fingerprint reader): This is "something you are", but the scenario specifically requires a physical token.

Why Not C (Secure token): Secure tokens are also valid but may not integrate as seamlessly into multi-factor authentication for physical and system access.

Why Not D (NFC scanner): An NFC scanner is a device and not a token itself; it reads cards or other credentials.

CompTIA A+ Exam Reference: Core 2 (220-1102), Section 2.5, access controls​.

D. Crimper:

A crimper is used to terminate an RJ45 cable properly by attaching the connector to the twisted-pair wires.

If the termination is not done correctly, the connection will be intermittent or fail entirely.

Incorrect Options:

A. Toner probe: Used to locate cables or trace their path, not for terminating RJ45 connectors.

B. Cable tester: Useful for testing connectivity but does not fix termination issues.

C. Punchdown: Used to connect wires to a patch panel or keystone jack, not for RJ45 connectors.

Key Takeaway: A crimper is the proper tool for fixing an improperly terminated RJ45 connection.

solution as

A screenshot of a network settings AI-generated content may be incorrect.

A screenshot of a computer AI-generated content may be incorrect.

A screenshot of a computer AI-generated content may be incorrect.

Firewalls are specifically designed to monitor, filter, and control network traffic using Access Control Lists (ACLs). ACLs define which traffic is allowed or denied based on parameters like IP address, protocol, or port.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.2 – Networking hardware and security:

“Firewalls use access control lists (ACLs) to allow or deny traffic based on rules. Unmanaged switches and PoE injectors do not support ACLs.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Networking Security Devices

CompTIA Exam Objectives 220-1101, Domain 2.2

============

Port flapping refers to a network port continuously going up and down, which can prevent the access point from fully coming online.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.4 – Wired and wireless troubleshooting:

“Repeated loss and restoration of network link is called port flapping and may result in network devices, such as access points, not coming online.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Network Troubleshooting

CompTIA Exam Objectives 220-1101, Domain 2.4

============

correct answer is "Overclocking" and "Reduce CPU Clock speed" CPU is at 4.5 Ghz when normal is 3.2 Ghz. Overclocking too much can cause freezes, and this is a gaming computer sothe user probably took it too far. http://blog.logicalincrements.com/2018/12/4-troubleshooting-tips-overclocking-pc/

Looking at the network configurations and outputs from both PCs and servers, here are the possible issues and solutions:

1. PC 1

Issue: The IP address for PC1 is 192.168.1.1, which conflicts with Server 1 (which also uses 192.168.1.1).

Solution: Change the IP address on PC1 to a unique one within the range, like 192.168.1.3.

2. PC 2

Issue: PC 2 is configured with 192.168.1.2, which conflicts with Server 2 that has the same IP address.

Solution: Update the IP address on PC 2 to something unique, like 192.168.1.4.

3. Server 1

Issue: The IP address for Server 1 is 192.168.1.1, which conflicts with PC1.

Solution: Since Server 1 and PC1 are using the same IP address, change one of them. For Server 1, you could change the IP address to 192.168.1.5.

4. Server 2

Issue: Server 2 is using the IP address 192.168.1.2, which conflicts with PC2.

Solution: Update Server 2 to use a different IP address, such as 192.168.1.6.

General Remediation:

The primary problem here is overlapping IP addresses, leading to connectivity issues. Each device on the network must have a unique IP address. After making these changes, ensure that all devices can communicate properly by testing the connection between devices and verifying they can access shared resources.

To boot from a USB drive, the user must configure the boot order in the system BIOS/UEFI to prioritize the USB device. This setting tells the computer to load the operating system from the USB device on startup.

From CompTIA A+ 220-1101 Official Study Guide, Objective 3.5 – Configure BIOS/UEFI settings:

“The boot order determines the sequence in which the system firmware attempts to find an OS to boot. Setting USB as the first boot device allows the computer to boot from a USB drive.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 3: BIOS/UEFI Configuration

CompTIA Exam Objectives 220-1101, Domain 3.5

============

A sandbox is an isolated virtual environment, often used for testing code or software safely without affecting the host system.

From CompTIA A+ 220-1101 Official Study Guide, Objective 3.7 – Virtualization:

“A sandbox provides an isolated environment, often implemented as a virtual machine, to safely test applications or code.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 3: Virtualization

CompTIA Exam Objectives 220-1101, Domain 3.7

============

If a printer is set to use a special tray (for cards/invitations) but a different type of print job is attempted (like a letter), a paper tray setting mismatch can cause errors. Changing the tray setting to match the print media resolves the issue.

From CompTIA A+ 220-1101 Official Study Guide, Objective 4.3 – Troubleshooting printers:

“If print jobs fail when media type changes, verify and adjust the paper tray settings to match the required output.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 4: Printer Troubleshooting

CompTIA Exam Objectives 220-1101, Domain 4.3

============