Pass the CompTIA A+ 220-1201 Questions and answers with ExamsMirror

Comprehensive and Detailed Step-by-Step Explanation:

To determine the correct device, we need to understand how a DOCSIS (Data Over Cable Service Interface Specification) network functions in a Small Office/Home Office (SOHO) environment:

C. Cable Modem:

A cable modem is required to convert the signal provided by the ISP (Internet Service Provider) over a DOCSIS network into a format that is usable by the local area network (LAN).

DOCSIS is a standard for high-speed internet over cable television infrastructure, and the cable modem acts as the gateway between the ISP ' s coaxial network and the LAN.

Without the cable modem, devices in the LAN would not be able to access the internet.

Degraded performance that occurs only during business hours strongly suggests network congestion caused by simultaneous data and voice traffic. According to CompTIA Core 1 (220-1201) networking objectives, combining voice (VoIP) and data traffic on the same network without proper segmentation can lead to latency, jitter, and packet loss, especially during peak usage periods.

Implementing VLANs (Virtual Local Area Networks) allows administrators to logically separate voice and data traffic, enabling better traffic management and prioritization. VLANs also support Quality of Service (QoS) policies that ensure time-sensitive voice traffic is prioritized over standard data traffic, improving call quality and overall performance.

Replacing switches with higher-capacity models is costly and unnecessary if proper traffic segmentation has not yet been implemented. Adding RAM to PCs or VoIP lines does not address network-level congestion. Firmware updates may improve stability but will not resolve sustained performance degradation caused by traffic contention.

CompTIA highlights VLAN implementation as a best practice for environments that use IP phones, especially when performance issues occur during high utilization periods.

Excessive heat buildup due to insufficient cooling is a primary cause of unexpected shutdowns. A high-performance heat sink improves thermal transfer, dissipates more heat, and helps maintain CPU temperature within safe limits. When CPU temperatures reach levels like 208°F (98°C), the system may shut down to prevent damage.

Mobile Device Management (MDM)software often controls access to corporate resources based onlocation, network, or VPN status. If the MDM is not configured to allow access from outside the office or via home networks, the apps may be blocked. This is the most probable cause if apps work only on-premises.

Option A:GPS is used for location services, not access control.

Option C:WPA is a Wi-Fi security protocol, not related to access restrictions.

Option D:NFC enables close-range communication irrelevant to app access.

CompTIA A+ Core 1 Exam Objective Reference:

Objective 1.6: Given a scenario, configure basic mobile device network connectivity and application support.

Badging is a form of authentication that requires employees to use a badge or ID card to release print jobs. This solution reduces unnecessary printing by ensuring only authorized users print.

Why Not A (Access control list): While ACLs manage permissions, they are not used for physical authentication at printers.

Why Not B (Audit logging): Audit logs track actions but do not restrict printer access.

Why Not D (Print server): A print server manages print jobs but doesn’t enforce authentication.

CompTIA A+ Exam Reference: Core 2 (220-1102), Section 2.5, authentication mechanisms​.

CompTIA A+ highlights that swollen or expanding batteries especially lithium-ion batteries can physically warp the laptop chassis, keyboard, or trackpad. This happens when internal chemical reactions cause the battery to swell. Distorted keyboards, bulging trackpads, and lifted chassis panels are classic symptoms of battery failure.

RAM and HDD issues do not cause physical deformation. A broken keyboard may malfunction electronically, but it will not bulge upward unless forced by something underneath typically an expanding battery.

The A+ safety domain also warns technicians not to puncture swollen batteries and to replace them immediately due to fire hazards.

Therefore, a failing (swollen) laptop battery is the most likely cause.

High resource usage along with frequentpop-upsare strong signs of amalware infection. The next logical step is toupdate anti-malware definitionsandrun a full scanto detect and remove threats.

Option A:Network performance is likely not the root cause local system behavior points to malware.

Option B:Drivers affect hardware functionality; they don’t resolve malware-related slowness.

Option D:DHCP issues usually cause IP conflicts or no network access, not CPU spikes or pop-ups.

CompTIA A+ Core 1 Exam Objective Reference:

Objective 4.2: Given a scenario, detect, remove, and prevent malware using appropriate tools and methods.

A fileshare becoming slow over time and then failing completely strongly suggests storage subsystem degradation, often due to a failing RAID array. CompTIA A+ explains that slow file access is an early sign of a degraded array, and eventual unavailability indicates the array may have failed or entered a critical state.

Since the technician can still RDP into the server, the OS is functioning, meaning memory is likely not the issue. Network connectivity is sufficient for remote login. Backup integrity does not affect real-time file availability.

Thus, the next step is to check the RAID array status, which directly controls the server’s storage performance and availability precisely what CompTIA identifies as the primary point of failure in such scenarios.

To provision and run multiple virtual machines on a physical server, the administrator must use a hypervisor. A hypervisor is the virtualization layer that creates, runs, and manages virtual machines by abstracting physical hardware resources such as CPU, RAM, storage, and network adapters into virtual resources presented to each VM. Once the server is configured with the required hardware support (such as sufficient RAM/CPU capacity and virtualization features enabled in firmware), the hypervisor is the component that enables VM creation, allocation of resources, virtual disk creation, and VM lifecycle actions like start, stop, suspend, snapshots, and virtual networking configuration.

Device Manager is used to view and manage hardware devices and drivers on an operating system, but it is not a VM provisioning tool. Disk Management can partition and format disks, which may support storage preparation, but it does not create or run VMs. A Virtual LAN is a network segmentation method at Layer 2 and may be used in VM networking designs, but it does not provide virtualization itself. Therefore, the correct tool for provisioning virtual machines is the hypervisor.

Tethering refers to sharing a mobile phone’s internet connection with another device, such as a laptop, either through USB, Bluetooth, or Wi-Fi. Tethering effectively turns the mobile phone into a personal hotspot for internet access.

Option A (IR): Incorrect. Infrared (IR) is used for short-range communication, such as remote controls, but it does not support internet sharing.

Option B (NFC): Incorrect. Near-field communication (NFC) is used for close-proximity data transfer, not for internet sharing.

Option C (Wi-Fi Direct): Incorrect. Wi-Fi Direct enables device-to-device communication but does not inherently provide internet sharing.

CompTIA A+ teaches that vertical lines on scanned or copied documents but not printed documents indicate a dirty or smudged scanner glass or ADF glass strip. Dust, ink smears, or debris create a line because the scanning sensor repeatedly passes over the same contaminated area.

If printing works normally, internal printer components such as the transfer roller or pickup rollers are not at fault. Maintenance kits apply to internal wear components like rollers, belts, or fusers not scanning artifacts.

Cleaning the scanner glass or ADF strip directly addresses this common problem. The A+ exam frequently includes troubleshooting questions about print vs. scan artifacts, and this scenario is a classic example.

Therefore, the correct solution is to clean the glass bed (or ADF strip).

The best answer is B. Moving to a supported system under a Type 2 hypervisor. The issue is application compatibility after an OS update. The Quentin Docter study guide explains that application virtualization is commonly used for legacy software or a legacy OS because older applications often run only on older operating systems. It further explains that virtualization allows users to run multiple environments without buying extra hardware, which directly matches the requirement for minimal cost and disruption. A Type 2 hypervisor runs on top of an existing host operating system, making it suitable for a department workstation scenario because users can keep the new supported OS while accessing the legacy application in a virtualized environment. A bare-metal Type 1 hypervisor is usually server-side and would be more disruptive and expensive. Migrating to a new product and importing data may be the long-term answer, but it introduces higher cost, retraining, and possible data loss. A private cloud does not solve OS compatibility by itself.

=========

Since only one user experiences the issue in a shared environment where everyone else has stable connectivity, CompTIA A+ suggests that the problem is most likely with the client device, not the network. The wireless card may be failing, overheating, or experiencing intermittent hardware faults.

If other Wi-Fi signals or EMI (electromagnetic interference) were the cause, multiple users would be affected. Frequency congestion (Option B) also impacts groups, not a single device.

CompTIA stresses that isolating whether the issue affects one user or many helps determine whether the fault lies with the network or device. Because the problem is isolated, the most probable cause is a malfunctioning wireless NIC in the user’s laptop.

When a laptop screen is replaced, the technician typically removes the display assembly components and works near the hinge area where the Wi-Fi antenna leads are routed. In most laptops, the Wi-Fi antennas are built into the display bezel and connect to the wireless adapter using thin coax cables labeled MAIN/AUX. If one or both antenna leads are left disconnected, pinched, or not fully seated during reassembly, the Wi-Fi adapter may still appear in the OS, but the radio signal strength becomes extremely weak. A common symptom is no SSIDs found or only very close/strong networks intermittently.

Bluetooth working does not rule this out because Bluetooth can have separate antennas or may still function at short range even when Wi-Fi reception is poor. Ethernet working confirms general network access and suggests the issue is isolated to the Wi-Fi radio path rather than the router, ISP, or OS networking stack. The wireless access point is unlikely to be the cause if the issue started immediately after hardware service and other devices can see SSIDs. Therefore, the first hardware check should be the wireless antenna connections and routing.