Pre-Summer Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code = getmirror

Pass the CWNP CWDP Wi-Fi Design CWDP-304 Questions and answers with ExamsMirror

Practice at least 50% of the questions to maximize your chances of passing.
Exam CWDP-304 Premium Access

View all detail and faqs for the CWDP-304 exam

Go to Exam

797 Students Passed

92% Average Score

95% Same Questions
Viewing page 3 out of 9 pages
Viewing questions 21-30 out of questions
Questions # 21:

What are the two types of WLAN discovery/scanning?

Response:

Options:

A.

Manual

B.

Hidden

C.

Active

D.

Passive

E.

Probe

F.

Automatic

Questions # 22:

An AP vendor being considered for a WLAN deployment suggests that their 2 4 GHz and 5 GHz dual-band APs use software defined radios What unique capability does this indicate in comparison to non-software defined radios?

Options:

A.

At least one radio can be configured for either 2 4 GHz or 5 GHz operations

B.

The radios can have their SSlDs configured through software

C.

Software is used to configure the encryption settings

D.

Software is used to configure the entire WLAN profile

Questions # 23:

The installation crew for your WLAN project wants to install a few APs to locations nearby the ones specified in the RF design document. What next step should occur?

Response:

Options:

A.

Confirm the mounting hardware.

B.

Choose a different AP model.

C.

Update the documentation.

D.

Consult the RF designer.

Questions # 24:

Even when a full pre-design site survey is not performed, what is always recommended to be performed within the deployment areas?

Options:

A.

A spectrum analysis walkthrough

B.

An AP-on-a-stick survey of 37% of the facility as this amount provides all of the statistical information required for good design

C.

A scan m the 5 GHz band looking for common loT interferes

D.

A scan in the Sub-i GHz bands to determine If sideband interference will impact 2 4 GHz operations

Questions # 25:

If radar has reportedly been detected on your WLAN deployment, what bands would you consider avoiding?

Response:

Options:

A.

5 GHz UNII-2 and 2e

B.

5 GHz UNII-2 and 3

C.

5 GHz UNII-2, 2e, and 3

D.

5 GHz UNII-1 and 2

E.

5 GHz UNII-1, 2, and 3

Questions # 26:

What is the meaning of a Real Time FFT graph?

Options:

A.

Real Time FFT means Real Time First Fundamental Trace and shows the value of the first signal detected on each frequency at each sweep

interval.

B.

Real Time FFT means Real Time Fast Frequency Timing and shows the RF pulses measured by the Layer 1 sweep tool.

C.

Real Time FFT means Real Time Fast Fourier Transform and shows the max value of the signal detected on each frequency in real time.

D.

Real Time FFT means Real Time Frequency Fundamental Texture and shows the value of the noise background generated by the card used

to perform the

E.

Real Time FFT means Real Time Fast Fourier Transform and shows the max value of the signal detected on each frequency in real time.

Questions # 27:

You're about to deploy an Enterprise-class VoWLAN infrastructure. You need to ensure that QoS is properly configured throughout the network.

What Access

Category (AC) should voice frames/packets use?

Options:

A.

AC_VI

B.

AC_VO

C.

AC_BE

D.

AC_BK

Questions # 28:

A business traveler from North America is in Europe. The hotel only provides coverage in 2.4 GHz. The traveler connects to the hotel's SSID and notices an AP in the hotel room.

However, the laptop reports a very low RSSI when connected. The traveler does not have the same problem when connecting in the lobby.

What would be the most likely cause of the low RSSI in the hotel room?

Response:

Options:

A.

The AP in the room is transmitting on channel 13 and the traveler associated to a non-channel 13 AP located elsewhere.

B.

The AP in the room is using Bluetooth instead of Wi-Fi.

C.

The AP in the room is using ZigBee instead of Wi-Fi.

D.

The switchport that the AP is connected to is only capable of transmitting at 10 Mbps.

Questions # 29:

When live video streaming solutions that transmit simultaneously to more than one recipient are used, what special capability should be

considered and configured in all affected WLAN implementations?

Options:

A.

IPSec

B.

IPv6

C.

Multicasting

D.

Secure TCP

Questions # 30:

You are validating association capabilities from clients to an 802.1X/EAP secure SSID. The RADIUS server's IP address is 10.100.50.25 and the

default RADIUS authentication port is used. When testing them, none of the clients are able to associate to the SSID. Troubleshooting the WLAN

infrastructure, you found out that the server is up and the RADIUS service is up as well, but the authenticator is not able to communicate properly

with the server. What's your next troubleshooting step?

Options:

A.

Verify that the shared secret between the authenticator and the RADIUS server is correct

B.

Reboot the clients

C.

Reboot the server

D.

Restart the RADIUS service

Viewing page 3 out of 9 pages
Viewing questions 21-30 out of questions
TOP CODES

TOP CODES

Top selling exam codes in the certification world, popular, in demand and updated to help you pass on the first try.

2V0-11.25
ADM-201
Agentforce-Specialist
CMMC-CCP
Data-Cloud-Consultant
PCNSE
PDI
PSE-Strata-Pro-24
Secure-Software-Design
Sharing-and-Visibility-Architect
Workday-Pro-Integrations
ZDTA