Pass the Huawei HCIP-Datacom H12-821_V1.0 Questions and answers with ExamsMirror

One multicast MAC address maps to 32 multicast IP addresses due to the limited number of bits used in the mapping process. Specifically, the lower 23 bits of the MAC address map to the lower 23 bits of the multicast IP address, while the high 24 bits of the MAC address are fixed as 0x01005E. Thus, Option B is false ​.

 Neighbor Discovery Protocol (NDP):

NDP is a key protocol in the IPv6 protocol suite, replacing ARP (Address Resolution Protocol) in IPv4.

It operates using ICMPv6 (Internet Control Message Protocol for IPv6) and is critical for managing interactions between IPv6 nodes on the same link.

 MQC and PBR

MQC (Modular QoS Command-Line Interface): Applied to interfaces for classifying and controlling traffic.

PBR (Policy-Based Routing): Used to influence packet forwarding based on policies rather than traditional routing tables.

Both MQC and PBR can be configured on device interfaces to filter incoming/outgoing packets or control their forwarding paths.

 HCIP-Datacom-Core Reference

The use of MQC and PBR on device interfaces is elaborated in the QoS and routing control chapters​​.

BGP does not advertise all routes learned from peers to other peers. By default, only the best (optimal) routes selected by BGP are advertised to other peers. Additionally, routes learned from IBGP peers are not forwarded to other IBGP peers unless a route reflector or confederation setup is used. The statement claiming all learned routes are advertised is false ​.

Understanding the Network Setup:

The OSPF network consists of three areas (Area 1, Area 0, and Area 2).

The server's subnet 192.168.1.0/24 is directly connected to R1 and imported into OSPF using the command:

import-route direct type 1 cost 2

The type 1 specifies the route as an OSPF Type 1 external route, meaning both the external cost and the internal OSPF cost will be included when calculating the total cost.

The external cost specified for the imported route is 2.

Cost Calculation to R2:

The interfaces between the routers are GE interfaces, and the default cost for GE interfaces is 1.

The path from R2 to the server goes through the following hops:

R2 → R1: Cost = 1 (intra-area link).

R1 → Server: External cost = 2 (specified in the import-route command).

Total cost to R2:

Intra-area cost (1) + External cost (2) = 3

Verification of Each Option:

Option A (2): Incorrect. This only accounts for the external cost, ignoring the internal OSPF cost.

Option B (4): Incorrect. This overestimates the cost by adding an extra hop.

Option C (3): Correct. The total cost is 3 (1 for the intra-area link + 2 for the external cost).

Option D (1): Incorrect. This ignores the external cost of the imported route.

The output shows that the router with the IP 10.0.12.2 is the Backup Designated Router (BDR), as indicated in the State: BDR field. The router ID is 10.0.2.2, the interface cost is 1, and the IP address of the interface is 10.0.12.2. Hence, C is the correct answer ​.

Edge ports are used in RSTP to bypass the spanning tree calculation for ports connected to end devices. By configuring ports like SWD's GE0/0/2 and SWC's GE0/0/2 as edge ports, they transition directly to the Forwarding state upon activation, ensuring faster convergence. Statement A is incorrect because receiving BPDU invalidates the edge port status ​.

Comprehensive and Detailed Step-by-Step Explanation:

1. Overview of AS_Path Attribute Modification:

The apply as-path command in a route-policy is used to modify the AS_Path attribute of routes. This is often required to influence the selection of routes or to adjust routing policies for incoming or outgoing BGP updates.

2. Parameters of the apply as-path Command:

Option A: Delete

Correct.

The delete parameter removes specific AS numbers from the AS_Path attribute. This is used to simplify or manipulate the AS_Path for specific routing policies.

Option B: Additive

Correct.

The additive parameter appends an AS number to the existing AS_Path attribute, instead of overwriting it. This is useful when you want to prepend AS numbers to influence route selection without removing the original AS_Path.

Option C: Copy

Incorrect.

The copy parameter is not supported in the apply as-path command for modifying AS_Path attributes.

Option D: Overwrite

Correct.

The overwrite parameter replaces the existing AS_Path with a new one. This provides complete control over the AS_Path attribute but removes the original AS_Path entirely.

3. Summary:

The valid parameters for the apply as-path command are delete, additive, and overwrite.

In IS-IS:

Level-1 routers can only form neighbor relationships with other Level-1 routers in the same area.

Level-2 routers can form neighbor relationships with other Level-2 routers regardless of area ID.

Level-1-2 routers can form relationships at both levels depending on the peer's configuration.

So, if two Level-1 routers have different area addresses, they cannot establish a neighbor relationship.

Reference from Huawei HCIP-Datacom-Core Technology Study Guide:

“Level-1 routers must have the same area address to establish neighbor relationships. Level-2 routers can peer across different areas.”

(Chapter: IS-IS Protocol Principles – Section: Neighbor Establishment)

Comprehensive and Detailed Step-by-Step Explanation:

Single-Hop BFD:

Single-hop BFD is used for detecting link failures in directly connected devices.

It uses UDP port 3784 for communication.

Multi-Hop BFD:

For multi-hop scenarios, BFD uses UDP port 4784 to ensure end-to-end connectivity.

Incorrect Options:

TCP ports 3784 and 4784 (C and D): BFD does not use TCP.