Pass the Huawei HCIP-Datacom H12-821_V1.0 Questions and answers with ExamsMirror

 IS-IS Interface Types

IS-IS interfaces are categorized based on physical link characteristics:

Point-to-Point (P2P): Direct connections between two routers.

Broadcast: Shared medium networks where multiple routers communicate.

 Incorrect Options

C. P2MP and D. NBMA are not standard interface classifications in IS-IS.

 HCIP-Datacom-Core Reference

IS-IS physical link classifications are elaborated in IS-IS link configuration sections​​.

ICMPv6 messages are classified into two types: error messages (e.g., Destination Unreachable, Time Exceeded) and informational messages (e.g., Echo Request, Echo Reply). This classification is fundamental to ICMPv6's operation ​.

IGMPv3 builds on IGMPv1 and IGMPv2 by supporting all previous query types, including General Query and Group-Specific Query, while introducing Source/Group-Specific Query. This enhancement allows finer control over multicast group membership ​.

 OSPF LSA Flooding Mechanism

If a router receives an LSA identical to one already in its LSDB, it does not flood the LSA again unless the LSA has changed (i.e., the sequence number or content has been updated).

OSPF ensures efficient use of bandwidth by avoiding redundant flooding of unchanged LSAs.

 HCIP-Datacom-Core Reference

The OSPF LSDB synchronization process explains that unchanged LSAs are not reflooded, ensuring stability and resource optimization​​.

In IPv6, fragmentation is handled only at the source node. Intermediate routers do not fragment packets. Instead, if a packet is too large for the next link, the router sends back an ICMPv6 Packet Too Big message to the source, which then adjusts its packet size.

This design:

Reduces processing load on intermediate devices.

Supports Path MTU Discovery (PMTUD).

Reference from Huawei HCIP-Datacom-Core Technology Study Guide:

“In IPv6, routers do not perform fragmentation. Only the source device fragments packets if needed, based on ICMPv6 feedback.”

(Chapter: IPv6 Fundamentals – Section: Fragmentation and PMTUD)

The filter-policy command in IS-IS is used to control the advertisement and filtering of routing information. However, it does not directly filter LSPs (Link State Packets); instead, it controls route advertisements. The false statement here is that it filters LSPs ​.

By default, BGP does not automatically summarize imported routes. Route summarization must be explicitly configured using the summary or similar commands ​.

Comprehensive and Detailed Step-by-Step Explanation:

1. What is the BFD Echo Function?

BFD (Bidirectional Forwarding Detection) is used to detect link failures.

The Echo function is an optional feature that tests link connectivity by looping back packets sent from the local device through the forwarding path.

2. Analysis of Each Statement:

Option A: If URPF is enabled on the peer end, BFD packets may be incorrectly discarded on the peer end.

Correct.

URPF (Unicast Reverse Path Forwarding) checks whether the source IP address of an incoming packet is reachable via the interface it was received on. Since the Echo function uses loopback packets, this can conflict with URPF, causing the packets to be dropped.

Option B: In the BFD Echo function, the device uses the IP address of the outbound interface as the source IP address by default.

Correct.

By default, the outbound interface's IP address is used as the source address for BFD Echo packets.

Option C: The BFD Echo function applies only to single-hop BFD sessions.

Incorrect.

The BFD Echo function can be used for both single-hop and multi-hop BFD sessions.

Option D: When configuring a BFD session supporting the BFD Echo function, you need to configure both the local and remote discriminators.

Incorrect.

The BFD Echo function is locally configured and does not require setting remote discriminators. The function operates independently of the remote device's configuration.

3. Summary:

The correct statements are A and B.

Access Control Lists (ACLs) can be classified into several types, including Basic ACL (filters based on source IP), Advanced ACL (filters based on multiple parameters like source and destination IP, protocol, and ports), and Layer 2 ACL (filters based on MAC addresses). User-defined ACLs are not a standard classification ​.