Pass the USGBC Leadership in Energy and Environmental Design (LEED) LEED-AP-BD+C Questions and answers with ExamsMirror

For LEED BD+C Materials and Resources (MR) Credit: Building Product Disclosure and Optimization – Sourcing of Raw Materials, Option 2, a product contributes based on its cost and sustainability attributes.

Given the bamboo entrance doors are Rainforest Alliance certified, and the glass inserts contain 100% pre-consumer recycled content, these materials qualify under the Leadership Extraction Practices.

The total material cost per door is $200.

The glass inserts ($150) are 100% pre-consumer recycled and count fully.

The bamboo ($50) also qualifies due to its sustainability certification.

Since only the glass contributes to the calculation, the total value contributing to the credit is $100 per door, or $100.00 total for both doors.

(Source: Official LEED BD+C Reference Manual)

To meet the Indoor Environmental Quality (IEQ) Prerequisite: Minimum Acoustic Performance for classrooms, sound pressure level measurements should be taken under conditions that reflect typical classroom use without occupants, ensuring accuracy in assessing HVAC background noise levels. Furnished, no occupants, HVAC operating at typical level (C) is the correct testing setup, as it accounts for sound absorption by furniture but excludes ambient noise from people. This setup provides a more accurate measure of the background noise levels produced by HVAC systems, ensuring compliance with acoustic performance requirements for optimal learning environments.

This alternative analysis can help the team check the impact of reducing the amount of concrete used in the building, which can affect several impact categories, such as global warming potential (GWP), acidification, and eutrophication1. Concrete is a material with high embodied energy and carbon emissions, and reducing its use can lower the environmental impact of the building2. Optimizing the slab depth can also improve the thermal performance and daylighting of the building, which can reduce the operational energy use and demand3.

Using plug-in devices can affect the energy performance of the building, which is one of the criteria for achieving Indoor Environmental Quality Credit. Thermal Comfort. The LEED v4 Reference Guide for Building Design and Construction states that "the project team must demonstrate that the proposed design meets the minimum energy performance requirements of ASHRAE Standard 90.1-2010, Appendix G, with errata"1. Plug-in devices are considered as part of the process loads in the energy model, and they can increase the energy consumption and demand of the building. Therefore, the project team must account for the plug-in devices in the energy model and ensure that the proposed design meets or exceeds the baseline performance rating.

Providing an educational program on the environmental and human health benefits of green building practices is a potential innovation strategy that is not addressed by any existing LEED credit. It also meets the criteria of being measurable, replicable, and having a positive impact on the project and the environment.

The surrounding residential density is calculated by dividing the total number of dwelling units by the total residential land area. In this case, it would be 780 dwelling units divided by 60% of 130 acres, which equals approximately 13 dwelling units per acre (or 32 dwelling units per hectare).

The nonresidential density, or Floor Area Ratio (FAR), is calculated by dividing the total nonresidential building floor area by the total nonresidential land area. In this case, it would be 1,600,000 ft² divided by 40% of 130 acres, which equals a FAR of approximately 0.47.

These calculations are used when attempting to achieve the Location and Transportation Credit, Surrounding Density and Diverse Uses, under the LEED AP BD+C V4 rating system.

To be eligible for LEED certification, a project must:

Be a permanent structure on existing land (floating structures like houseboats do not qualify).

Have a defined site boundary (mobile homes do not meet this requirement unless they are permanently installed).

Have a minimum floor area of 250 square feet (23.2 m²) (so a 900 ft² office qualifies).

Prefabricated buildings (Option A) may qualify if they are permanently installed.

Houseboats (Option C) and mobile homes (Option D) are not eligible unless permanently located.

The new office building (Option B) meets all LEED requirements and is the correct answer.

(Source: Official LEED BD+C Reference Manual)

According to the LEED v4 Reference Guide for Building Design and Construction, no smoking signage must be placed within 10 feet (3 meters) of every building entrance, except for alarmed emergency exits. This applies to both the main entrance and the service entrances, regardless of their location or frequency of use. The signage is intended to communicate the no-smoking policy to occupants and visitors and prevent environmental tobacco smoke from entering the building. References: EQ Prerequisite Environmental Tobacco Smoke Control, LEED v4 Reference Guide for Building Design and Construction123

Detailed Explanation:

In a cold climate, additional envelope insulation is the most effective strategy for reducing energy costs. Improved insulation minimizes heat loss through the building envelope, reducing the demand for heating systems. This aligns with LEED’s focus on enhancing energy efficiency and thermal performance in building design.

Minimum Energy Performance

A project’s massing and site orientation can have a direct impact on the minimum energy performance prerequisite, which requires projects to demonstrate a percentage of energy cost savings compared to a baseline building. Massing and orientation affect the amount of solar heat gain, daylight availability, natural ventilation potential, and wind exposure of the building, which in turn influence the heating, cooling, lighting, and ventilation loads and strategies. By optimizing the massing and orientation of the building, projects can reduce their energy consumption and improve their thermal and visual comfort.