Pass the USGBC Leadership in Energy and Environmental Design (LEED) LEED-AP-BD+C Questions and answers with ExamsMirror

These design elements are examples of low-impact development (LID) and green infrastructure (GI) practices that can reduce runoff volume and improve water quality by replicating the natural hydrology and water balance of the site1. Cisterns can collect and store rainwater for reuse or infiltration, porous pavement can allow water to seep into the ground, swales can convey and filter stormwater runoff, and vegetated roofs can reduce runoff and evapotranspiration2.

This option requires the project team to calculate the weighted daily average of the number of trips per day for each qualifying route, using the formula provided in the LEED v4: Building Design + Construction Guide. This option ensures that the transit service frequency is accurately represented and meets the minimum thresholds for weekday and weekend trips, as shown in Table 1 and Table 2 of the guide.

Green Infrastructure (GI) and Low-Impact Development (LID) rainwater management strategies improve upon the conventional approach for rainwater management by replicating a site’s natural hydrology. GI and LID are design approaches that use various practices to mimic the natural water cycle and reduce the negative impacts of development on the environment. They aim to preserve, restore, or create natural features that can capture, infiltrate, evaporate, or reuse rainwater on site, rather than conveying it to a centralized stormwater system. By doing so, they can reduce runoff volume and peak flow, improve water quality, enhance groundwater recharge, increase biodiversity, and create more attractive and resilient landscapes. Therefore, option A is the correct answer. The other options are not true for GI and LID strategies. Discharging rainwater at a faster rate (option B) would increase the risk of flooding, erosion, and pollution downstream. Increasing a site’s impervious surface (option C) would reduce the infiltration and evaporation of rainwater and increase runoff and heat island effects. Providing a greater volume of rainwater detention (option D) would not necessarily improve the site’s hydrology, as detention is only a temporary storage of rainwater that does not address the runoff quality or quantity issues. For more information on GI and LID rainwater management strategies, you can refer to the LEED v4 Reference Guide for Building Design and Construction1 or the Green CE course on Rainwater Management for LEED v4.1 Projects2.

Exemplary Performance is not available for Option 2 of Location and Transportation Credit, Surrounding Density and Diverse Uses. According to the LEED v4 BD+C Reference Guide, this credit has two options: Option 1. Surrounding Density (5 points) and Option 2. Diverse Uses (1 point). Exemplary Performance is only available for Option 1, and it requires achieving a surrounding density of at least 405,000 square feet per acre (100,000 square meters per hectare)1. Option 2 does not have any Exemplary Performance criteria, and it only requires locating the project within a 1/2-mile (800-meter) walking distance of at least seven diverse uses2. References:

Credit: Surrounding density and diverse uses | U.S. Green Building Council

Surrounding Density and Diverse Uses - LEED v4

LEED BD+C Location and Transportation (LT) Credit: High Priority Site encourages development in locations with existing infrastructure to promote sustainable land use.

Option 1: Historic District applies to projects located in designated historic districts where at least 75% of land within ½ mile (0.80 km) is previously developed.

Brownfields (Option C) and Federal Renewal Communities (Option D) are separate site categories that fall under different High Priority Site options.

The ¾ mile (1.20 km) radius in Option A is incorrect, as LEED specifically sets the requirement at ½ mile (0.80 km).

To earn this credit under Option 1, a project in a historic district must demonstrate that the surrounding land is predominantly redeveloped.

(Source: Official LEED BD+C Reference Manual)

The make and model of fixtures is required in determining the baseline for the Water Efficiency Prerequisite, Indoor Water Use Reduction. This information is used to calculate the baseline water consumption of the building, which is then compared to the proposed water use to determine the percentage reduction.

When calculating the reverberation time of a room, the operating sound level of the nearest HVAC equipment is the least relevant piece of information. The reverberation time is the time it takes for the sound to decay by 60 decibels after the source stops emitting sound. The reverberation time depends on the volume and the surface area of the room, as well as the sound absorption coefficients of the materials that cover the surfaces. The height and width of the room are needed to calculate the volume and the surface area. The noise reduction coefficient of the ceiling surface and the sound absorption coefficient of the floor surface are needed to calculate the total sound absorption of the room. The operating sound level of the nearest HVAC equipment is not relevant for calculating the reverberation time, but it may affect the background noise level and the speech intelligibility in the room.

ENERGY STAR® (C) provides tools recognized by the U.S. Green Building Council (USGBC) that assist with energy management strategies, benchmarking, and procurement guidelines. ENERGY STAR offers resources for energy performance benchmarking, operational efficiency, and product standards, which help project managers optimize energy use in line with LEED requirements. Green Seal (A) and SCAQMD (B) focus on materials and emissions, while SMACNA (D) provides guidelines for air quality management.

According to the LEED v4 Reference Guide for Building Design and Construction, diverted construction waste is defined as "materials that are diverted from disposal in landfills or incineration facilities and are instead reused, recycled, composted, or salvaged"1. Asphalt with aggregate is an example of a material that can be recycled and reused for paving or other applications. Excavated soil and land-clearing debris are excluded from the calculation of the total construction and demolition waste for the MR Credit Building Life-Cycle Impact Reduction1. Alternative daily cover is a material that is used to cover the surface of an active landfill at the end of each day to control odors, pests, and litter. It is not considered as diversion because it does not reduce the amount of waste sent to landfills2. References: MR Credit Building Life-Cycle Impact Reduction, LEED v4 Reference Guide for Building Design and Construction3142

Detailed Explanation:

For the Brownfield Remediation option under the High-Priority Site credit, the project site must include contaminated soil or groundwater requiring cleanup to improve environmental conditions. This credit incentivizes the redevelopment of previously unusable or hazardous sites, helping to promote environmental restoration and sustainable land use.